NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
2
INTRODUCTION
This appliance complies with National
Safety Standards and is tested and listed
by OMNI-Test Laboratories Inc.; Beaverton,
Oregon (Report No. 116-F-15-5) to ANSI
Z21.88-2002 (in Canada, CSA-2.33-2002),
and CAN/CGA-2.17-M91 in both USA and
Canada, as vented gas fi red room heater.
TABLE OF CONTENTS
Packaging List
page 2
Introduction page
2
General Information
page 3
Questions/Building Offi cials
page 4
High Altitude
page 4
Fireplace Requirements
page 4
Specifi cations
page 5
Clearance to Combustibles
page 7
Step 1 Preparation
page 8
Step 2 Clean Fireplace
page 8
Step 3 Unpack the insert.
page 9
Step 4 Lift Insert into Position
page 9
Step 5 Remove Glass Door
page 9
Step 6 Remove Firebox Contents
page 9
Step 7 Install LP Conv. (if necessary) page 9
Step 8 Install Venting
page 9
Step 9 Connect Gas Line
page 12
Step 10 Purge Air
page 12
Step 11 Install Log Set
page 13
Step 12 Reinstall Front Glass Door
page 14
Step 13 Perform Leak Test
page 14
Step 14 Install Surround Assembly
page 14
Step 15 Install Wall Thermostat
page 14
Step 16 Check Appliance Operation
page 14
Step 17 Perform Spillage Test
page 16
Step 18 Check Blower Operation
page 16
Step 19 Adjust Burner
page 17
Step 20 Install Louver Kit
page 17
Rating Plates
page 18
PLEASE READ AND UNDERSTAND THESE
INSTRUCTIONS BEFORE BEGINNING
YOUR INSTALLATION.
This installation manual will help you obtain
a safe, effi cient, dependable installation for
your appliance and vent system.
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW GAS APPLIANCE MANU-
FACTURED BY LENNOX HEARTH PRODUCTS.
When you purchased your new gas fi red heater, you joined the ranks of thousands of
concerned individuals whose answer to their home heating needs refl ects their concern for
aesthetics, effi ciency and our environment. We extend our continued support to help you
achieve the maximum benefi t and enjoyment available from your new gas fi red heater. It
is our goal at Lennox Hearth Products to provide you, our valued customer, with an appli-
ance that will ensure you years of trouble free warmth and pleasure.
Thank you for selecting a Lennox Hearth Products gas fi red heater as the answer to
your home heating needs.
Sincerely,
All of us at Lennox Hearth Products
PACKAGING LIST
The assembled vented gas fi replace heater
is packaged with:
• One accessory package containing a
literature package (installation and operation
instruction manuals) is located on top of the
appliance.
• One log set, one bag of embers, one bag of
vermiculite, one propane conversion kits.
• One Warranty Certifi cate.
• One Fireplace Warning Label.
• One Draft Hood Sliding Tool.
This gas fi replace heater is a natural con-
vection, heat circulating gas fi replace insert
designed for residential applications.This
heater is designed to be installed into an exist-
ing masonry or factory built solid fuel burning
fi replace only - Masonry fi replace must be
built to UBC 37 or ULC S628 standards and
factory built (zero clearance) fi replace must be
listed to UL 127 or ULC S610. Units must use
a 4” listed B-Vent or listed liner (conforming
to UL 1777) from the appliance outlet to the
chimney termination. The venting system
must be routed through the existing fi replace
fl ue system to the vent termination.
This millivolt appliance is designed to oper-
ate on natural gas or propane gas only.
A millivolt gas control valve with piezo igni-
tion system provides safe, effi cient operation.
External electrical power is required to operate
the blower.
This appliance may be used with a thermo-
stat (see Optional Wall Thermostat). This
appliance is certifi ed for use in bedrooms.
If installed in a bedroom in Canada, a ther-
mostat IS required.
This appliance requires an adequate supply
of combustion and ventilation air. As an
aid in determining whether or not these
requirements have been satisfi ed, follow the
procedure indicated in the section entitled
Spill Test Procedure (see page 16).
The millivolt appliance is manually con-
trolled and features a spark igniter (piezo)
that allows the appliance's pilot gas to be
lit without the use of matches or batteries.
This system provides continued service in
the event of a power outage.
This unit is factory set for use with Natural
Gas and will require a fi eld conversion for use
with Propane (other fuels are NOT allowed).
The use of other fuels or combination of fuels
will degrade the performance of this system
and may be dangerous.
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THE APPLIANCE OR ITS
COMPONENTS. ANY MODIFICATION OR ALTERA-
TION MAY VOID THE WARRANTY, CERTIFICATION
AND LISTINGS OF THIS UNIT.
Installation must conform to local codes. In
the absence of local codes, installation must
comply with the current National Fuel Gas
Code, ANSI Z223.1. (In Canada, the current
CAN-1 B149 installation code.) Electrical
wiring must comply with the National Elec-
trical Code ANSI/ NFPA 70 - latest edition.
In Canada, the current CSA C22-1 Canadian
Electrical Code - latest edition.
MODEL: EBVI30
SKS-30, Surround Kit, Small
(40 1/4" W x 27 1/2" H)
SKM-30, Surround Kit, Medium
(45 3/4" W x 30 1/4" H)
SKL-30, Surround Kit, Large
(49 1/4" W x 30" H)
MODEL: EBVI25
SKS-25, Surround Kit, Small
(41 1/16" W x 26 1/16" H)
SKM-25, Surround Kit, Medium
(44 1/8" W x 27 5/8" H)
SURROUND ASSEMBLY SOLD SEPA-
RATELY
Содержание EVB125
Страница 19: ......
