background image

2

   

Abrasive

surfaces

Risk of injury by

moving objects

High

temperatures

Low

temperatures

Risk of injury by

rotating objects

Electrical

voltage

ELECTRICAL CONNECTIONS

Make sure to switch off the power before installing, repairing or carrying out maintenance on the unit, 

in order to prevent serious electrical injury.

Keep local and national legislation in mind when installing the unit.

Standard Guidelines to Lennox  equipment

All technical data contained in these operating instructions, including the diagrams and technical description remains 

the property of Lennox  and may not be used (except for the purpose of familiarizing the user with the equipment), 

reproduced, photocopied, transferred or transmitted to third parties without prior written authorization from Lennox. 

The data published in the operating instructions is based on the latest information available. We reserve the right to 

make modifications without notice.

We reserve the right to modify our products without notice without obligation to modify previously supplied goods.

These operating instructions contain useful and important information for the smooth operation and maintenance of 

your equipment.

The instructions also include guidelines on how to avoid accidents and serious damage before commissioning the 

equipment and during its operation and how to ensure smooth and fault-free operation. Read the operating instructions 

carefully before starting the equipment, familiarize yourself with the equipment and handling of the installation and 

carefully follow the instructions. It is very important to be properly trained in handling the equipment. These operating 

instructions must be kept in a safe place near the equipment.

Like most equipment, the unit requires regular maintenance. This section concerns maintenance and management 

personnel.

If you have any queries or would like to receive further information on any aspect relating to your equipment,  

do not hesitate to contact us.

POINTS TO BEAR IN MIND

DANGER AND WARNING SIGNS

Содержание COMPACTAIR CDC

































Отзывы: