background image

©2018 Lennox Industries Inc. 

Dallas, Texas, USA

Page 1

THIS MANUAL MUST BE LEFT WITH THE 

HOMEOWNER FOR FUTURE REFERENCE

 WARNING

Improper installation, adjustment, alteration, service 

or maintenance can cause property damage, personal 

injury or loss of life. Installation and service must  be 

performed by a licensed professional HVAC installer or 

equivalent, service agency, or the gas supplier.

 IMPORTANT

The Clean Air Act of 1990 bans the intentional venting of 

refrigerant (CFCs, HCFCs and HFCs) as of July 1, 1992. 

Approved methods of recovery, recycling or reclaiming 

must be followed. Fines and/or incarceration may be 

levied for noncompliance.

INSTALLATION 

INSTRUCTIONS

MULTI-POSITION AIR HANDLERS

507836-01

3/2018

Merit

®

 Series  

CBX25UH-T Air Handler Units 

50 Hz

Shipping and Packing List 

Package 1 of 1 contains: 

1 –  Assembled air handler unit factory-equipped for upflow 

or horizontal air discharge application (includes upflow 

and horizontal drain pans and 

preinstalled air filter

).

Check the air handler for shipping damage; if found, im-

mediately contact the last carrier. Check the unit rating 

plate to confirm that delivered unit matches order. 

General Information 

The CBX25UH air handler is designed for indoor instal-

lation only. As shipped, the unit is ready for installation 

in either upflow, horizontal left-hand or right-hand air dis

-

charge applications. Air filters and other accessories are 

available and listed in the CBX25UH Product Specification 

bulletin (EHB) for ordering.
All units are shipped with a factory-installed check/expan-

sion valve. 
This instruction is intended as a general guide and does 

not supersede local or national codes in any way. Consult 

authorities having jurisdiction before installation. 

 CAUTION

As with any mechanical equipment, contact with sharp 

sheet metal edges can result in personal injury. Take 

care while handling this equipment and wear gloves and 

protective clothing.

IMPORTANT INFORMATION FOR INSTALLER

This unit has a delay relay that delays the supply blower “ON” for 1 second and keeps the blower “ON” for 45

seconds on all fan and cooling demands. 

1

SECOND

DELAY

OFF

100%

L/s

100%

L/s

45

SECS

COOLING

DEMAND

1

2

3

4

Содержание CBX25UH-024





















Отзывы: