background image

506257-01

Issue  1330

Page  29  of  29

Allied Air Enterprises Inc. (“Allied Air”) provides its air conditioning and heating products with a Standard  Limited Parts Warranty for five (5) years.  This additional 5-Year Limited 

Extended Parts Warranty is in addition to and is intended to supplement Allied Air’s Standard Limited Parts Warranty.  As such, Allied Air provides for a total of 10-years of limited 

warranty coverage (Standard Limited Parts Warranty plus additional 5-Year Limited Extended Parts Warranty). 

This 5-Year Limited Extended Parts Warranty applies only to the original purchaser of the equipment and cannot be transferred.  If during the coverage period, a covered part fails 

because of a defect in materials or workmanship under normal use and maintenance, Allied Air will provide a free replacement part to the purchaser through a licensed service 
contractor utilizing an authorized Allied Air distributor.   The purchaser must pay shipping costs and all other costs of warranty service.  Allied Air will not pay labor involved in 

diagnostic calls or in removing, repairing, servicing or replacing parts.

EXTENDED COVERAGE -

PARTS/COMPRESSORS

Covered equipment and parts are warranted by Allied Air for a total of 

10 YEARS

 (Standard Limited Parts Warranty) from installation, except as provided below

HEAT EXCHANGERS

Covered residential heating equipment’s heat exchanger is warranted by Allied Air for a LIMITED LIFETIME from date of original installation, except as provided below.  

EXCLUDED COMPONENTS -

The following components are expressly not covered by this 5-Year Limited Extended Parts Warranty: cabinets, cabinet pieces, air filters, driers, refrigerant, refrigerant line sets, 
belts, wiring, fuses, oil nozzles, unit accessories, R-22 compressors, and any parts not affecting unit operation.

 

If this 5-Year Limited Extended Warranty does not apply, then parts are warranted under the Standard Limited Parts Warranty for a period of 

5 YEARS 

and  heat exchangers for 

20 YEARS

.  If the Standard Limited Parts Warranty periods differ from the original warranty certificate, the periods stated on the original warranty certificate apply.

This 5-Year Llimited Extended Parts Warranty does not apply to, and no warranty is offered by Allied Air, on any unit ordered over the internet.  Proof of purchase may be 

required.

Any part replaced pursuant to this 5-Year Limited Extended Parts Warranty is warranted only for the unexpired portion of the limited extended warranty term remaining for the 
original part.  The installation of replacement parts under the terms of this 5-Year Limited Extended Parts Warranty does not extend the warranty period.

Steps for obtaining replacement parts under this 5-Year Limited Extended Parts Warranty:

If you suspect a defect in your equipment, please contact the installer of the unit to obtain assistance.  If unsuccessful, please contact an Allied Air dealer or 

distributor in your area.  If unable to obtain local assistance, refer to Allied Air’s website (

www.alliedair.com

) or contact Allied Air at 800-448-5872.

Allied Air is 

specifically not responsible for:

1. Damage or repairs required as a result of flood, fire, wind, lightening strike (to the home or unit), corrosive atmosphere, contact with corrosive material  (chlorine, fluorine, salt, 

recycled waste water, fertilizers or other damaging substances) or other conditions beyond the control of Allied Air;

2.  

Use of parts, accessories, or refrigerant not compatible with the unit;

3.  

Modification, change or alteration of the unit, except as expressly directed in writing by Allied Air;

4.  

Improper use, accident, neglect or unreasonable use or operation of the unit, including operation of electrical equipment at voltages other than the range specified on the 

unit     nameplate;

5.  

Operation with system parts (indoor unit, outdoor unit and refrigerant control devices) which are not ARI matched or do not meet the specifications  recommended by Allied Air;

6.  Damage or repairs required as a consequence of faulty or installation or application;
7.  

Normal maintenance as described in the installation and operating manual, such as cleaning of coils, filter cleaning and/or replacement and lubrication;  

 and 

8. Changes in the appearance or sound of the unit that do not affect its performance.

This 5-Year Limited Extended Parts Warranty is an extension of Allied Air’s Standard Limited Parts Warranty. 

 ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS 

FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE TERM OF THIS LIMITED EXTENDED WARRANTY.  

Some states and provinces do 

not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

ALLIED AIR SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO EXTRA UTILITY EXPENSES OR 

DAMAGES TO PROPERTY.

 Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may 

not apply to you

The parties intend this writing as a final expression of their agreement with respect to warranties.  Allied Air makes no other warranty beyond that which is expressly 

contained in this writing.

Allied Air shall not be liable for any default or delay in performance under this warranty caused by any contingency beyond its control, including the unavailability of replacement parts.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state or province to province.

Excludes residents of states or provinces where registration requirements are prohibited, such as California and Quebec.  Residents of these states or provinces may either register as noted above or 

provide proof of when the unit was purchased and installed, such as an original invoice from the contractor with the Owner’s name, address, purchase date, serial and model number. 

5-YEAR LIMITED EXTENDED PARTS WARRANTY

  1.    The unit is an Armstrong Air, AirEase, Ducane, or Concord branded unit;

2.  The unit is installed in a residential application, which is an owner-occupied single-family residence.  No commercial applications are allowed;

3.  The unit is properly registered at 

www.alliedair.com with Allied Air within 60-days after the original date of installation or occupancy.

1

  To register, 

follow the directions and complete the online warranty registration at www.alliedair.com

.  For customer inquiries, contact Allied Air at 1-800-448-

5872. 

4.  The unit is part of a complete ARI matched system and installed by a state certified or licensed contractor in accordance with the unit installation, operation, 

and maintenance instructions provided with the unit.

5.  Coils and air handlers are covered only when they are branded Armstrong, AirEase, Ducane, Concord or ADP and are purchased and newly installed as 

a system along with a qualifying unit.  Except for ADP-branded products, coverage of other third party coils and air handlers are specifically excluded from 

this 5-Year Limited Extended Parts Warranty.

6.   Installation of the unit takes place on or after October 3, 2008.

 REQUIREMENTS FOR EXTENDED COVERAGE-

Содержание Allied Air 4HP18LT- 24






























Отзывы: