Lennox 100017 Скачать руководство пользователя страница 44

Страница: 44 / 52

Table 2. Alert Codes and Troubleshooting

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), PA=Pure Air S, ZA=Zone system and TS=Thermostat

Alert

Code

Inverter

Flash

Code

Priority

Condition

Actual Displayed

Alert Text

Under dealer

control center >

Notifications

Component or System Operational State and Troubleshooting Tip

How to clear alert code

700

Service

Urgent

Thermostat

Temp Sensor

Problem

The HD display’s internal temperature sensor is not operating correctly. To resolve this issue, try

the following:
•

Remove HD display from mag-mount and reattaching.

• Seal hole in wall behind mag-mount to minimize exposure to unconditioned air from inside the

wall.

• Run “

reset all

” under dealer control center.

•

If issue persist, then replace the HD display.

Automatically clears when the system

detects that the issue no longer exists.

701

Service

Urgent

Thermostat

Temp Above

Limit

The thermostat is reading indoor temperatures above the pre-programmed limit. The thermostat

has a built-in non-adjustable high limit of 99°F.
• Cool thermostat.

• Adjust set point.
• Run

reset all

under dealer control center.

•

Replace HD display or mag-mount, if needed.

Automatically clears when the system

detects that the issue no longer exists.

703

Service Soon

Thermostat

Humid Sensor

Problem

Thermostat Humid Sensor Problem. Sensor is damaged or data is corrupted possibly.

First try a system reset, then if persists the

thermostat would need replacement.

900

Service Soon

(moderate)

Temperature

Control Problem

Something is causing the system not to be able to reach set point. Check for dirty coil, low

refrigerant or verify the system is not under size for the application.

Automatically clears when the system

detects that the issue no longer exists.

901

Service Soon

(moderate)

Smart Alert

Modes: Heating

& Cooling

This feature is disabled by default. Go to dealer control center and enable feature under Smart

Hub.
This alert occurs when temperature consistently diverges away from set-point in the following two

conditions:
• When system is running high stage/full speed.

• When the system is not providing demand when there is a call for one. Typically when system

locked out.

The cooling capacity alert doesn’t work in zoning.

If alert code exist must be manually cleared

by resetting power.

3000

Maintenance

Replace Filter 1 Not Applicable

Reset filter reminder for both

3001

Maintenance

Replace Filter 2 Not Applicable

3002

Maintenance

Replace

Humidifier Pad

Not Applicable

Reset Humidifier pad reminder

3003

Maintenance

Replace UV

Bulb

Not Applicable

Reset UV Light reminder

3004

Maintenance

Reminder

Not Applicable

Make service appointment with dealer and

reset reminder

Содержание 100017





















































Результаты поиска

Содержание 100017

Отзывы:

Похожие инструкции для 100017

Бренды по названию

Популярные бренды

Lennox 100017, Руководство пользователя

Результаты поиска

Содержание 100017

Отзывы:

Похожие инструкции для 100017

Бренды по названию

Популярные бренды