Lennox 100017 Скачать руководство пользователя страница 49

Страница: 49 / 52

Table 2. Alert Codes and Troubleshooting

GF= Gas Furnace, AH=Air Handler, ID=Indoor unit (GF or AH), HP=Heat Pump, AC=Air Conditioner, OD=Outdoor Unit (AC or HP), PA=Pure Air S, ZA=Zone system and TS=Thermostat

Alert

Code

Inverter

Flash

Code

Priority

Condition

Actual Displayed

Alert Text

Under dealer

control center >

Notifications

Component or System Operational State and Troubleshooting Tip

How to clear alert code

Service Soon

Possible loose, incorrectly wired connections or two zone sensors are assigned the same zone

number. Two dashes will be displayed on the S30/S40 thermostat for indoor temperature and/or

zone sensor then
• System will go into central mode.

• Individual zone functions is disabled.

If two zone sensors are assigned the same

zone number, this could cause the double

dashes to appear. If loose or incorrectly

wired connection was confirmed, correct

the issue and run the re-configuration

procedure.

Содержание 100017





















































Результаты поиска

Содержание 100017

Отзывы:

Похожие инструкции для 100017

Бренды по названию

Популярные бренды

Lennox 100017, Руководство пользователя

Результаты поиска

Содержание 100017

Отзывы:

Похожие инструкции для 100017

Бренды по названию

Популярные бренды