background image

10

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Shown with Tubinox™ Stainless 

Steel Liner components (see Page 

29 for ordering information)

Chimney 

Termination

Cap

Chimney 

Termination

Rain Cap

Masonry 

Adaptor

Length

90° Tee

Storm

Collar

Roof

Flashing

Flashing

Ceiling Support

Assembly

Slip

Adaptor

Chimney

Connector

6” x 24” 24-gage 

black steel or 26 

gage blued steel 

single wall pipe

Single Wall Pipe

Using 6” Diameter Single Wall Connector Pipe

STAINLESS STEEL LINER

Using 6” Diameter Rigid Stainless Steel Liner

Figure 6 - Typical Installation

Figure 7 - Connected to a Masonry Chimney

Floor

Protector

Floor

Protector

Fasten each stove pipe 

connection with at least 

3 sheet metal screws.

Single wall stove pipe 

must not pass through 

attics, closets, walls or 

ceilings. It is used to 

connect this appliance 

to a factory built or 

masonry chimney.

INSTALL VENTING SYSTEM PER VENT MANUFACTURERS 
INSTRUCTIONS!

INSTALL VENTING SYSTEM PER VENT MANUFACTURERS 
INSTRUCTIONS!

Fasten stove pipe to 

flue collar with 3 sheet 

metal screws.

YOUR  CHIMNEY  INSTALLATION  MUST  COMPLY  WITH  LOCAL 

BUILDING AND FIRE CODES.

Содержание Grandview GV230

































Отзывы: