background image

3

IMPORTANT SAFETY AND WARNING 

INFORMATION

READ THIS MANUAL IN ITS ENTIRETY AND UNDER-

STAND THESE RULES TO FOLLOW FOR SAFETY.

Pl

an

ni

ng

 In

st

al

la

tio

n

Sa

fe

ty

 a

nd

 G

en

er

al

In

st

al

la

tio

n

Op

er

at

io

n

M

ai

nt

en

an

ce

Tr

ou

bl

es

ho

ot

in

g

Pa

rts

 / 

Ac

ce

ss

or

ie

s

1.  When this room heater is not properly installed, a house 

fire may result. To reduce the risk of fire, follow the instal-

lation instructions. Contact local building or fire officials 

about restrictions and installation inspection requirements 

in your area. 

2.  Wear gloves during installation to avoid injury from sharp 

edges on the stove and/or its parts.

3.  This unit is designed and engineered to burn only dry, well-

seasoned wood. Burning wet wood will greatly reduce the 

stove’s efficiency, produce excessive amounts of smoke 

and can cause dangerous chimney fires due to creosote 

build-up.

4.  Before opening the door, the draft control must be fully open 

to avoid possible combustion flash (ignition of hot volatile 

gases as the door is opened).

5.  Never use gasoline, gasoline-type lantern fuel, kerosene, 

charcoal lighter fluid, or similar liquids to start or ’freshenup’ 

a fire in this heater. Keep all such liquids well away from 

the heater while it is in use. DO NOT USE CHEMICALS OR 

FLUIDS TO START THE FIRE.

6.  While burning, fuel utilizes oxygen from the air in the room. 

Be sure to allow an adequate amount of fresh air into the 

room where the stove is burning.

7.  The outside surface of the stove will be hot while burning 

properly and can set items like clothing and curtains on 

fire.  Keep  furnishings  and  other  combustible  materials 

away from the stove. Using the heat from the stove to dry 

wet clothing can be hazardous if clothes are placed too 

near the surface of the stove.

8.  HOT WHILE IN OPERATION.  KEEP CHILDREN, CLOTHING 

FURNISHINGS AND COMBUSTIBLE MATERIAL A CONSIDER-

ABLE DISTANCE AWAY.  CONTACT MAY CAUSE SKIN BURNS. 

Do not allow children to play near the stove without close 

supervision. Do not touch the stove while it is burning. 

Use extreme caution while the unit is in use. Surface tem-

peratures become dangerously hot and can cause serious 

burns.

9.  Do not allow anyone to operate the stove who is not familiar 

with the operating instructions.

10.  Attempts to achieve heat output rates that exceed stove 

design specifications can result in permanent damage to 

the stove. Never leave your stove unattended on high burn 

rates. This may cause overfiring. Overfiring the stove may 

cause a house fire. If the stove glows, you are overfiring.

11.  Keep a water hose or hand-operated fire extinguisher close 

for safety.

12.  Smoke Detectors - Since there are always several poten-

tial sources of fire in any home, we recommend installing 

smoke detectors. If possible, install the smoke detector in 

a hallway adjacent to the room (to reduce the possibility 

of occasional false activation from the heat produced by 

the stove).  If your local code requires a smoke detector 

be installed within the same room, you must follow the 

requirements  of  your  local  code.  Check  with  your  local 

building department for requirements in your area.

13.  Inspect your chimney at least once a month during the burn-

Sa

fe

ty

 a

nd

 G

en

er

al

ing season to check for soot and creosote accumulations. 

Any accumulations over 1/8” thick should be removed by 

a professional chimney sweep. Do not attempt to burn out 

heavy creosote accumulations with a hot fire. If large ac-

cumulations are occurring, review your burning procedures.

14.  If a creosote fire should develop, the fire department should 

be called immediately and then attempts should be made 

to control the fire until assistance arrives. If a “runaway” 

fire should develop causing over-heating of the stove, the 

door and draft regulators should be closed immediately. 

The fire should die down once deprived of oxygen. After a 

severe chimney fire, the complete chimney system should 

be checked before further use.

15.  Do Not Use Grate Or Elevate Fire - Build Wood Fire Directly 

On Hearth (firebrick). Do not use andirons or other methods 

of supporting the fuel. 

16.  Please read this entire manual before you install and use 

your new room heater. Failure to follow instructions may 

result in property damage, bodily injury, or even death.

17.  Check all local building and safety codes before installation. 

The installation instructions and appropriate code require-

ments must be followed exactly and without compromise. 

In the absence of local codes the following standards and 

codes must be followed.

18.  In the U.S.A, install in accordance with the National Fire 

Protection Association’s Code, NFPA 211, Standards for 

Chimneys, Fireplaces, Vents and Solid-Fuel-Burning Appli-

ances, or similar regulations, may apply to the installation 

of a Solid-Fuel-Burning appliance in your area. In Canada, 

the guideline is established by the CSA Standard, CAN/

CSA-B365-M93, Installation Code for Solid-Fuel-Burning 

Appliances and Equipment.

19.  DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY 

AIR  DISTRIBUTION  DUCTWORK  UNLESS  SPECIFICALLY 

APPROVED FOR SUCH INSTALLATIONS.

20.  WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL) 

CAN RESULT IN CARBON MONOXIDE POISONING, WHICH 

MAY LEAD TO DEATH! 

21.  Carbon Monoxide Poisoning – Early signs of carbon monox-

ide poisoning resemble the flu with headaches, dizziness, 

or nausea.  If you have these signs, get fresh air at once!  

Have the heater inspected by a qualified service technician.  

Some people are more affected by carbon monoxide than 

others.  These include pregnant women, people with heart 

or lung disease or anemia, those under the influence of 

alcohol, and those at high altitudes.

22.  Failure  to  use  manufacturer  provided  parts,  variations  in 

techniques and construction materials or practices other than 

those described in this manual may create a fire hazard and 

void the limited warranty.

23.  Do not make any make-shift compromises during installa-

tion. Any modification or alteration may result in damage 

to the appliance or dwelling and will void the warranty, 

certification and listings of this unit.

24.  These appliances are designed as supplemental heaters. 

Therefore, it is advisable to have an alternate heat source 

when installed in a dwelling.

25.  Do Not Overfire – If Heater or Chimney Connector Glows, 

You Are Overfiring.

26.  DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERV-

ING ANOTHER APPLIANCE.

27.  DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH 

AS GASOLINE, NAPHTHA OR ENGINE OIL.

Содержание Grandview GV230

































Отзывы: