LENCO RC-8-2 Скачать руководство пользователя страница 5

8.  Press the [SET] key once, the LCD shown AUTO     TV001 and the RC-8-2 
is now performed the auto search count from the code you set up before, for 
example TV 001...and so on. 
9.  If the TV turn off. This indicates that the RC-8-2 is now set to your TV. 
10.  Press the [SET] key to save the working code. The LCD shown as 
SUCCESS and the RC-8-2 is now ready to operate your TV. 
11.  To check the code, press the [POWER] key to ON position. Press the 
[CH+/-], [VOL+/- * * ], *, and other applicable keys.   If no function, repeats Steps 
1-11. 
12. In any cases if you need to leave the auto search, just press the [ESC] key to 
exit, the LCD will be shown as EXIT and back to normal operation mode. 
13.  To program other equipment, repeats the Steps 1-11 for your VCR, SAT, 
AUD and or your second TV or VCR or SAT, etc..  

Press the [SET] key to for 2 seconds 
Press & release the [CH+] 
Press the [SET] key once, and than press the [CH+] key once for AUTO 
SEARCH 
Press the [DEVICE] key to select a desired mode 
Press the [SET] key to save the working code  

SETTING UP BY QUICK/MANUAL SEARCH 
This manual search method checks all its preprogrammed codes to find the code 
that will operate your equipment. This method may take a few minutes.  
1.  Make sure your TV is switched on (not on standby). 
2.  Aim the RC-8-2 at your TV. 
3.  Press the [SET] key to for 2 seconds and the LCD will be shown CODE 
SETUP.  
4.  Press & release the [CH+] key once to view the CODE SRCH page. 
5.  Upon the LCD shown CODE SRCH, press the [SET] key once, the LCD 
shown as TV QUICK SRCH. Press the [Device] key to select a desired mode (TV, 
VCR, SAT or AUD, etc..). In this case is [TV] key. 
6.  Press the [SET] key once, the LCD shown as HAND TV001 and the RC-8-2 
is now performed the quick/manual search count from the code you set up before, 
for example TV 001...and so on. 
7.  Now, press & release the [CH+] key slowly until the TV turns off. This 
indicates that the RC-8-2 is now set to your TV. (During the quick/manual search, 
you can press the [CH-] key as backward searching.) 
8.  Press the [SET] key to save the working code. The LCD shown as 
SUCCESS and the RC-8-2 is now ready to operate your TV. 
9.  To check the code, press the [POWER] key to ON position. Press the 
[CH+/-], [VOL+/- * * ], *, and other applicable keys.   If no function, repeats Steps 
1-9. 
10.  In any cases if you need to leave the quick/manual search, just press the 
[ESC] key to exit, the LCD will be shown as EXIT and back to normal operation 
mode. 

Содержание RC-8-2














Отзывы: