LENCO RC-8-2 Скачать руководство пользователя страница 4

7.  Your RC-8-2 is now programmed to operate your TV. Write down your TV 
code on the label at the back of the RC-8-2 for future reference. 
8.  To program other equipment, repeats the Steps 1-7 for your VCR, SAT, AUD 
and or your second TV or VCR or SAT, etc.... 
NOTE : To exit from the DIRECT CODE SETUP during the code entering, just 
press the [ESC] key once and back to normal operation mode.  

Press the [SET] key to for 2 seconds 
Press & release the [SET] key 
Input 3 Digit TV code 
Code accepted 
Code error  

IMPORTANT FOR AUTO SEARCH AND QUICK/MANUAL SEARCH 
Before the use of either Auto Search or Quick/Manual Search, please read 
careful of below requirement: 
Device Mode for TV    

Assigned for TV searching. 

Device Mode for VCR   

Assigned for VCR searching. 

Device Mode for SAT   

Assigned for SAT searching. 

Device Mode for AUD   

Assigned for AUD searching. 

Device Mode for AUX1  

Need to set up the selected device code first in 

order to search proper for assigned device   
Device Mode for AUX2  

Need to set up the selected device code first in 

order to search proper for assigned device   
Device Mode for AUX3  

Need to set up the selected device code first in 

order to search proper for assigned device   
Device Mode for AUX4  

Need to set up the selected device code first in 

order to search proper for assigned device   

P.4 
SETTING UP BY AUTO SEARCH 
This auto search method checks all its preprogrammed codes to find the code 
that will operate your equipment automatically. This method may take a few 
minutes.  
1.  Make sure your TV is switched on (not on standby). 
2.  Aim the RC-8-2 at your TV. 
3.  Press the [SET] key to for 2 seconds and the LCD will be shown CODE 
SETUP. 
4.  Press & release the [CH+] key once to view the CODE SRCH page. 
5.  Upon the LCD shown as CODE SRCH, press the [SET] key once, the LCD 
shown as TV QUICK SRCH. 
6.  Press the [CH+] key once, the LCD shown as TV AUTO SRCH.   (** Press 
the [CH-] key once, it did backward to TV QUICK SRCH.) 
7.  Press the [Device] key to select a desired mode (TV, VCR, SAT or AUD, 
etc..). In this case is [TV] key. 

Содержание RC-8-2














Отзывы: