background image

15

 

Replace the used battery.

 

Ensure the battery cover is replaced and the
locking screw tightened, before further use.

Fig. 7

Battery Replacement

6.  WARRANTY

Your  LEM HEME clamp on power meter is
guaranteed for one year from the date of purchase
against defective material or workmanship. If the
meter fails during the warranty period, we shall at our
discretion, repair or replace it with a new or
reconditioned unit  provided we are satisfied that the
failure is due to defective material or workmanship.  To
make a claim under warranty, the meter should be
returned to us, postage prepaid, with a description of
the defect.  The use of a battery, other than that
specified invalidates this warranty.
Goods alleged by the buyer to be defective shall not
form the subject of any claim for injury, loss, damage,
or any expense howsoever incurred whether arising
directly or indirectly from such alleged defects other
than death or personal injury resulting from the seller‘s
negligence.
No condition is made or to be implied nor is any
warranty given or to be implied as to the life or wear of
goods supplied or that they will be suitable for any
particular purpose or for use under specific conditions,
notwithstanding that such purpose or conditions may
be made known to the seller.

7.  OTHER PRODUCTS

Содержание LH1050


















Отзывы: