Leica Captivate Скачать руководство пользователя страница 767

Страница: 767 / 1060

A DTM job is required.

45.4

The Toolbox

45.4.1

Overview

Press

Tools

on any page of the Stake/Check panel.

The toolbox contains additional functionality for each of the stake and check

methods. This functionality is additional to those already existing functions

which are available via the function keys.
The functionality differs between the stake and check methods. Refer to these

subchapters for a detailed description of the functionalities:

•

"45.4.2 Use heights from DTM"

•

"45.4.3 Apply current chainage"

•

"45.4.4 Get current angle to alignment"

•

"45.4.5 Stake individual point"

•

"45.4.6 COGO Road - Alignment info"

•

"45.4.7 COGO Road - Create points"

•

"45.4.8 Additional Layer Info"

•

"45.4.9 Box / base definition"

•

"45.4.10 Get current slope"

•

"45.4.11 Manual Slope"

•

"45.4.12 Reset slope to design"

•

"45.4.13 Shift reference line"

•

"45.4.14 Recalculate chainage"

•

"45.4.15

Stake intersection point

45.4.2

Use heights from DTM

This menu function is available for the following stake/check methods: Line,

local line, surface grade, crown, layer.

The app offers the possibility to

•

switch to a height which is retrieved from an existing height layer, as

defined in the selected DTM job. The layer from the DTM is applied and

used as a height reference for the staking out or checking of alignments.

•

retrieve heights from an existing layer, as defined in the DTM job associ-

ated with the project. The DTM used is not considered for the stake values.

Three new information lines are added to the page:

DTM height diff

DTM height

and

DTM layer

•

show the DTM triangles in the planar view and in the cross section view in

3D viewer.

Once defined, each layer remains active until it is turned off. DTM heights can

be used for both 2D and 3D alignments.

Required elements

Access

Description

Availability

Description

Roads - Road

767

Содержание Captivate





































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Captivate

Отзывы:

Похожие инструкции для Captivate

Бренды по названию

Популярные бренды

Leica Captivate, Техническое справочное руководство

Результаты поиска

Содержание Captivate

Отзывы:

Похожие инструкции для Captivate

Бренды по названию

Популярные бренды