LEGRAND Wattstopper DCLV2 Скачать руководство пользователя страница 2

2

LOAD TYPES

Use the DCLV2 for these load types:

•  0 to 10V electronic dimming ballasts (Mark 7 or equivalent) 

with maximum of up to 50mA.

•  Compatible LED systems (verify compatibility with LED control 

manufacturer).

TERMINAL BLOCK

The DCLV2 has a wiring terminal block with 7 positions:

1 24VDC input
2 Common
3 0–10V Violet
4 Sensor input
5 Control Output
6 0–10V Gray
7 Common

DIMMING MODE

The DCLV2 supports low-voltage DC dimming, using Class 2 

wires. Multiple circuits can use the same dimming signal without 

additional power equipment.

0–10V Dimming curves

To accommodate various types of ballasts, the DCLV2, executes 

a straight proportional relationship between the internal level and 

the voltage provided, 0.75VDC to 9.5VDC.

0–10V Dimming (with ON/OFF option)

•  When the user ramps up, relay 1 output 

switches from 0V to 24VDC. This closes 

the power pack relay to supply line 

voltage to the light fixtures.

•  When the user ramps down and the 

0–10V output becomes 0V, relay 1 

switches to 0V. This opens the power 

pack relay to remove power to the 

light fixtures. This allows the ballast to 

smoothly ramp down and then be turned 

OFF.

NOTE: 

An ON to OFF transition can take 

longer than expected (by about 2 

seconds) because the DCLV2 is 

dimming down. The OFF to ON 

transition is immediate.

WIRING EXAMPLES, LIGHTING CONTROL

Neutral

Hot

White

Black

Red

Red

Fixture

**Ground

Red

Blac

k

Blue

Orange

Brown

Gray

Low Voltage Wires

24VDC

0–10V

Control

0–10V

Common

Red

Violet

Gray

Black

Power Pack

BZ Series

DCLV2

Blue

Sensor

Blue

0-10V wiring diagram

Neutral

Hot

White

Black

Red

Red

Fixture

Sensor

Ceiling/Wall

24VDC

Any

**Ground

Red

Blac

k

Blue

Orange

Brown

Gray

Low Voltage Wires

24VDC

0–10V

Sensor

Control

0–10V

Ground

Common

Red

Violet

Gray

Black

Black

Control Output

+24VDC

Red

Common

Power Pack

BZ Series

DCLV2

Blue

Blue

Blue

Sensor input wiring diagram

Ballast ON/OFF control wiring diagram

To control a simple ON/OFF system do not connect the 0-10V output on 

the DCLV2.

Neutral

Hot

White

Black

Red

Red

Fixture

**Ground

Red

Blac

k

Blue

Orange

Brown

Gray

Low Voltage Wires

24VDC

Control

Common

Red

Black

Power Pack

BZ Series

DCLV2

Blue

Sensor

Blue

%277202)',00(5

7232)',00(5

NOTES

Any BZ series power pack will work with the DCLV2, but the 

following should be noted:

•  The Orange, Brown, and Gray wires on the BZ-150 and  

BZ-250 are not used and should be capped.

•  The Manual/Auto On switch on the BZ-150 and BZ-250 

should be left in the Auto-On position. Manual functionality is 

handled by the DCLV2.

•  The BZ-200 and BZ-250 must be grounded to ensure signal 

integrity,not for safety ground.

WARNING:

 TURN THE POWER OFF AT THE 

CIRCUIT BREAKER BEFORE WIRING.

Содержание Wattstopper DCLV2













Отзывы: