Doc No. FM0600 issue I Page 6
13. QUICK SETUP MODE - CONTINUED
Repeat as above to set the Stop Time then press the
ENTER
key – the display will change to “
Another Time Slot? No
”
Use the
key to select
Yes
to enter more time slots or press
the
ENTER
key.
The display will go back to the “
set on/off times
” menu, press
the
key to move to the next option;
⊳
Would you like an
instant alarm ?
yes = enter, next =
⊳
Press the
ENTER
key and the display will change to
“
Instant Alarm? No
”
Use the
keys to choose
Yes
or
No
then press
ENTER
.
If you choose
Yes
an alarm will be sent immediately the
person leaves their bed/chair.
The display will go back to the “
instant alarm
” menu, press
the
key to move to the next option;
⊳
Would you like a delay
before an alarm ?
yes = enter, next =
⊳
Press the
ENTER
key and the display will change to
“
Enter Time Delay; 00 Mins
”
Use the
keys to set the delay before an alarm from
1 to 99 Minutes then press the
ENTER
key.
The display will go back to the “
delay before alarm
” menu,
press the
key to move to the next option;
⊳
Would you like a
NOT IN BED alarm ?
yes = enter, next =
⊳
Press the
ENTER
key and the display will change to
“
Not in Bed Alarm; No
”
Use the
keys to choose
Yes
or
No
then press
ENTER
.
If you choose
No
the monitoring will start when the person is
detected in bed.
If you choose
Yes
the display will change to
“
Not in Bed Alarm; How Long? 000 Mins
”
Use the
keys to set the not in bed alarm from 0 to 999
minutes then press the
ENTER
key (an alarm will be sent if the
person is not in bed after this period).
The display will go back to the “
not in bed alarm
” menu, press
the
key to move to the next option;
⊳
Would you like a
STILL IN BED alarm ?
yes = enter, next =
⊳
Press the
ENTER
key and the display will change to
“
Still in Bed Alarm; No
”
Use the
keys to choose
Yes
or
No
then press
ENTER
.
If you choose
No
the monitoring will end at the end of the
monitoring period.
If you choose
Yes
, the display will change to
“
Still in Bed Alarm; How Long? 000 Mins
”
Use the
keys to set the still in bed alarm from 0 to 999
minutes then press the
ENTER
key (an alarm will be sent if the
person is still in bed after this period).
The display will go back to the “
still in bed alarm
” menu, press
the
key to move to the next option;
⊳
Would you like to
calibrate sensor ?
yes = enter, next =
⊳
Note: this option is not relevant for Magic Sticks, SensAlert
or Aux sensors.
If using a standard bed/chair sensor press the
ENTER
key and
the display will change to “
Put Sensor Under Mattress/Chair
”
and “
Press ENTER When Ready
”
Place the sensor under the mattress or chair cushion then
press the
ENTER
key.
The display will show “
30 Secs Left …PLEASE WAIT…
” and
count down to zero while the sensor is being calibrated.
The display will go back to the “
calibrate sensor
” menu, press
the
key to move to the next option;
⊳
Would you like to
go into test mode ?
yes = enter, next =
⊳
Press the
ENTER
key and the display will change to;
Test Mode
…….. No Client ……..
⊳
exit
Get the client to lie on the bed/sit in the chair and the display
should show “
….. Client Detected…..
”
Remain on the bed/chair for 10 seconds and the display will
show “
Unit is sending status IN code
”
After a short delay (when the IN status is being transmitted)
the display should show “
….. Client Logged IN…..
”
Get the client off the bed/out the chair and the display will
show “
Unit is sending status OUT code
”
After a short delay (when the OUT status is being transmitted)
the display should show “
….. Client OUT…..
”
After 10 seconds the unit will start to beep and the display will
show “
….. Alarm…..
”
After a further 10 seconds and the display will show “
Unit is
sending ALARM code
”
End of Test Mode.
Note: if the client is not detected as in the bed/chair then you
may need to adjust the sensitivity – go to the
Advanced
Setup
Calibrate and Test
Change Sensitivity
option.
See page 9.
The display will go back to the “
test mode
” menu, press the
key to move to the next option;