LEGRAND Finelite HP-4 Скачать руководство пользователя страница 9

Страница: 9 / 9

HP-4 Wet Location Surface Mount Installation Instructions

9 of 9

TE: 09/09/19

tooltipp

too p

oo p

tooltipp

ID: 1

ID: 2

ID: 3

Final Step - Replace Backplates, Diffusers & Diffuser Covers

•

NOTE: If your installation includes a battery backup, please see addendum (98333) that should be

included with your kitting package.

•

Reinstall any open backplates by rotating into luminaire body and snapping back into clips.

•

Remove diffusers from protective plastic bag.

•

CAUTION: Wear gloves to keep diffuser surface clean, take care to wipe off any water or condensation

on diffusers before installing into luminaire.

•

CRITICAL: Be sure to install correct diffuser to its corresponding luminaire ID.

•

Install diffusers into luminaire body, ensuring they snap into place.

•

Reinstall all endcap and joint diffuser covers.

•

Turn power on to luminaire.

Joint Diffuser Cover

Endcap Diffuser Cover

Step 7 - Closing Luminaires

Endcap Diffuser Cover

(provided)

Joint Diffuser Cover

(provided)

#6-32 x 3/8" Screw

(provided)

Содержание Finelite HP-4










Результаты поиска

Содержание Finelite HP-4

Отзывы:

Похожие инструкции для Finelite HP-4

Бренды по названию

Популярные бренды

LEGRAND Finelite HP-4, Руководство по установке

Результаты поиска

Содержание Finelite HP-4

Отзывы:

Похожие инструкции для Finelite HP-4

Бренды по названию

Популярные бренды