background image

6/16 

 

ELIOT Kit STOP&GO Connected 

 

Cat. N°: 4

 149 54

 

 

 

4. PREPARATION - CONNECTION

 (continued)

 

On site information displayed by the Stop&Go: 
Stop&Go lockout: 

. By the sliding front face. 

Sliding front face downward: the associated device goes into OFF 
position and manual or automatic closing operations are disabled. 
Sliding front face upward: the device is operating. 

. Lockout by padlock Φ 4mm, only when the sliding front face is 

down. 

Then mechanical and electrical controls are not possible. 

Display of the device status and the status of the contacts of 
the associated device: 

. By handle mark: 

“O

-

Off“ white on a green

 background = device switched-off and 

contacts opened. 

“I

-

On” white on a red background = device powered

-on and 

contacts closed. 

Device handle status: 

. The handle of the Stop&Go, consists of two parts: 

an “isolating” handle

 

a “power” handle

 

 

. Operation sequences: 

“Normal situation”: both handles upward.

 

 

 

 

4. PREPARATION - CONNECTION

 (continued)

 

On site information displayed by the Stop&Go 

(continued)

Device handle status 

(continued)

. Operation sequences 

(continued)

In case of an “Unwanted tripping” of the associated device and 

during the verification of the state of the electric circuit: 

the power handle is down. 
the isolating handle is up. 

The Stop&Go can be remotely controlled via the Smartphone 

app 

 

 

- If the Stop&Go detects a permanent fault after a tripping or a too 
recurrent non-permanent fault (3 faults and 3 remote closing 
operations in a time of 5 minutes), the isolating handle goes down 

The Stop&Go cannot be anymore remotely controlled via the 

Smartphone app 

 

 

Note: 

Refer to the § Details for “too recurrent” non

-

permanent faults” 

for all details on recurrent faults 

Resetting by the Stop&Go handle:  

. The local resetting of the Stop&Go and of the associated device 
can be carried out by the Stop&Go handle (isolating and power 
handles together) 

 

 

 

 

 

 

 

 

 

Technical data sheet: F02465EN/01 

Updated: 28/03/2019 

Created: 06/10/2016 

 

 

 

Isolating handle 

Power handle 

Isolating handle 

Power handle 

Isolating handle 

 

Power handle 

 

Isolating handle 

Power handle 

Isolating handle 

Power handle 

Содержание 4 149 54

















Отзывы: