LEGRAND 0 026 72 Скачать руководство пользователя страница 25

Страница: 25 / 29

25/29

Technical data sheet: S000114123EN-1

Updated:

Created: 18/01/2021

Cat. No(s): 0 026 72/73/74/76/78/79

KNX controller multi-application DIN

7 . COMMUNICATION OBJECTS (continued)

7 .10 "Fan Coil" parameter (continued)
7 .10 .3 "A/B1 - Automatic Operation" parameter

Object value “automatic ON/OFF” switch

on to automatic

: automatic operation is activated by a telegram with value 1

: automatic operation is inactivated by a telegram with value 0

Threshold value OFF <--> speed 1 In %

[0…100]

0…

*10

…100

Threshold value speed 1 <--> speed 2 In %

[0…100]

0…

*30

…100

Threshold value speed 2 <--> speed 3 In %

[0…100]

0…

*70

…100

A fan level switches on when its command value lower limit is reached

or exceeded.

Hysteresis threshold

Value in % +/- [0…20]

0…

…100

The fan level switches off again as soon as its command value lower

limit minus the hysteresis is undershot again.

Minimum dwell period in fan speed In s

[0…65535]

…65535

This parameter defines the dwell time for a fan speed of the fan until it

switches to the next higher or lower fan speed.

: no delay time for switching.

7 . COMMUNICATION OBJECTS (continued)

7 .10 "Fan Coil" parameter (continued)
7 .10 .4 "A/B1 - Direct Mode" parameter

Enable communication object

“Switch speed x” 1 bit

yes

*no

The data format for the fan level feedback is defined as 1 bit. Separate

three objects are defined separately for each fan level. If several ON/

OFF telegrams are received consecutively in a short period of time

at various communication objects Fan speed 1…3, the value last

received by the fan control is the decisive value.

Enable communication object

“Fan speed UP/DOWN” 1 bit

yes

*no

With multiple manual UP or DOWN switching, the target speed will

be increased or reduced by a speed step. This is possible until the

maximum or minimum possible speed is achieved.

Enable communication object

“Fan speed switch” 1 byte

yes

*no

This parameter is enabled “Fan speed switch” communication object

with percentage 0…100%.

CONTENTS

Содержание 0 026 72






























Результаты поиска

Содержание 0 026 72

Отзывы:

Бренды по названию

Популярные бренды

LEGRAND 0 026 72, Руководство пользователя

Результаты поиска

Содержание 0 026 72

Отзывы:

Бренды по названию

Популярные бренды