Lectronics RM Скачать руководство пользователя страница 18

Страница: 18 / 24

SMB/EO1 Series

LECTROSONICS, INC.

Before going through the following chart, be sure that you have a good battery in the transmitter. It is important that
you follow these steps in the sequence listed.

SYMPTOM

POSSIBLE CAUSE

TRANSMITTER PWR LED OFF

1) Battery is inserted backwards or dead.

2) Transmitter not powered up. (See

Operating Instructions,

Power UP and Boot Sequence.

)

TRANSMITTER PWR LED BLINKS GREEN EVERY FEW SECONDS, TRANSMITTER
DOES NOT RESPOND OTHERWISE

1) Transmitter has been put to sleep by the remote control.

%ITHERUSETHEREMOTECONTROLTOWAKEITUPAGAINORREMOVE

ANDREINSERTTHETRANSMITTERSBATTERY

AUDIO LEVEL LEDs NOT LIGHTING

1) Gain control set to minimum.

"ATTERYISDEADORINSTALLEDBACKWARDS#HECK072,%$

3) Mic capsule is damaged or malfunctioning.

-ICCABLEDAMAGEDORMISWIRED

RECEIVER RF INDICATOR OFF

1) Transmitter not turned on, or is in Standby Mode.

2) Transmitter battery is dead.

3) Receiver antenna missing or improperly positioned.

4) Transmitter and receiver not on same frequency.

#HECKSWITCHESDISPLAYONTRANSMITTERANDRECEIVER

5) Transmitter and receiver not on same frequency block.

/PERATINGRANGEISTOOGREAT

7) Defective transmitter antenna.

NO SOUND (OR LOW SOUND LEVEL), RECEIVER INDICATES PROPER AUDIO MODULATION

1) Receiver output level set too low.

2ECEIVEROUTPUTDISCONNECTEDORCABLEDEFECTIVEORMISWIRED

3) Sound system or recorder input is turned down.

DISTORTED SOUND

1) Transmitter gain (audio level) is far too high. Check audio level

,%$SANDRECEIVERAUDIOLEVELSDURINGUSE

2) Receiver output may be mismatched with the sound system or

recorder input. Adjust output level on receiver to the correct

level for the recorder, mixer or sound system.

5SETHERECEIVERS4ONEFUNCTIONTOCHECKLEVEL

3) Transmitter is not set to same frequency as receiver. Check

that operating frequency on receiver and transmitter match.

2ECEIVER4RANSMITTER#OMPATIBILITY-ODEMISMATCHED

EXCESSIVE FEEDBACK

1) Transmitter gain (audio level) too high. Check gain adjustment

ANDORREDUCERECEIVEROUTPUTLEVEL

2) Talent standing too close to speaker system.

-ICISTOOFARFROMUSERSMOUTH

Troubleshooting

Содержание RM

























Результаты поиска

Содержание RM

Отзывы:

Бренды по названию

Популярные бренды

Lectronics RM, Инструкция по эксплуатации

Результаты поиска

Содержание RM

Отзывы:

Бренды по названию

Популярные бренды