Leclerc Looms 1009-0000 Скачать руководство пользователя | Manualshive

Страница: 18 / 24

background image

Unhook brake treadle cord C from the brake realease treadle.

Hold circular wire brake shoe D up slightly to the rear of the loom.

Insert one end of the warp beam (which has only a metal post) into the left-hand

side back post.

Insert the friction brake drum of the warp beam into the circular

wire brake shoe D.

Do not unroll the brake shoe (brake circle), just slide the warp

beam into it

PAGE 18

«
...
16
17
18
19
20
...
»

Содержание 1009-0000

























Отзывы:

Нет отзывов

Похожие инструкции для 1009-0000

Бренд: Pfaff Страницы: 52

Memory Craft 6300P

Бренд: Janome Страницы: 69

Бренд: TAJIMA Страницы: 140

Бренд: Sinbo Страницы: 48

Бренд: MyBinding Страницы: 3

Бренд: Count Страницы: 27

Бренд: JK Audio Страницы: 16

Бренд: Mercury Страницы: 6

K 70/30 Bp Pack Adv.

Бренд: Kärcher Страницы: 28

Бренд: UnionSpecial Страницы: 68

Бренд: JUKI Страницы: 52

Бренд: Nilfisk-Advance Страницы: 28

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 9

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды