Leclerc Looms 1009-0000 Скачать руководство пользователя | Manualshive

Страница: 13 / 24

background image

Slide jack box B between posts A and A', from bottom to top, and
affix it to blocks C and C' using eight 1½" (40 mm) round-headed
screws no. 12.

PAGE 13

The tape (Saran Wrap) holding the jack box must
now be removed.

The ratchet pawl Q affixed to the side of the

loom must be lifted up while inserting the Jack

Box.

Q

«
...
11
12
13
14
15
...
»

Содержание 1009-0000

























Отзывы:

Нет отзывов

Похожие инструкции для 1009-0000

Бренд: Xerox Страницы: 298

Panafax UF-8000

Бренд: Panasonic Страницы: 187

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 6

Бренд: Panasonic Страницы: 65

Бренд: Singer Страницы: 100

Бренд: Singer Страницы: 24

Бренд: Titan Страницы: 33

Бренд: Weslo Страницы: 24

Surface Prep Machine 390

Бренд: Sinclair Страницы: 13

Бренд: Strobel Страницы: 32

Бренд: JUKI Страницы: 4

Бренд: Sandia Plastics Страницы: 13

Бренд: Husqvarna Страницы: 20

KENMORE 385. 1254180

Бренд: Kenmore Страницы: 56

Sewing machine cabinet 272.98100.490

Бренд: Kenmore Страницы: 13

SEARS 385. 17622

Бренд: Kenmore Страницы: 52

Kenmore 385.19106

Бренд: Kenmore Страницы: 71

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды