Leclerc Looms 1009-0000 Скачать руководство пользователя | Manualshive

Страница: 16 / 24

background image

PAGE 16

Install the treadle cord with the treadle hook.

Using the carriage bolts, steel washers and square nuts, attach the batten sley A (with shuttle

race) to the batten swords B.

Then affix the batten handtree C to the batten swords B.

Install reed D in the slots of batten handtree C and

batten sley A.

Adjust batten handtree C by sliding the bolts in the

slots of the batten swords to firmly hold the reed.

«
...
14
15
16
17
18
...
»

Содержание 1009-0000

























Отзывы:

Нет отзывов

Похожие инструкции для 1009-0000

Бренд: Janome Страницы: 59

Бренд: Janome Страницы: 42

HQ Sweet Sixteen

Бренд: Handiquilter Страницы: 41

Бренд: handi quilter Страницы: 2

MARCY PLATINUM MS-91

Бренд: MPEX Страницы: 11

Бренд: Saeco Страницы: 36

Бренд: Radio Shack Страницы: 36

Бренд: Riccar Страницы: 22

Бренд: Baby Lock Страницы: 56

Бренд: Racing Страницы: 22

Бренд: Singer Страницы: 7

1500 Contractors

Бренд: MasterCraft Страницы: 8

Бренд: Pacific Страницы: 8

Бренд: Baum Страницы: 49

Бренд: Racing Страницы: 3

Бренд: GBC Страницы: 18

Бренд: JUKI Страницы: 34

Бренд: JUKI Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды