Leadshine ELD5 Series Скачать руководство пользователя страница 71

Страница: 71 / 81

User Manual for ELD5 Servo

(V1.00)

www.leadshine.com

Table 7.7 Parameter setup of Operation Mode Selection

Mode

Parameter

Specification

Position mode

PA_001=20

The position control is performed based on the positional command
(pulse train) from the host controller or the command set in the
servo driver.

Velocity mode

PA_001=21

The velocity control is performed according to the analog speed
command from the host controller or the speed command set in the
servo driver.

Torque mode

PA_001=22

The torque control is performed according to the torque command
specified in the form of analog voltage or the command set in the
servo driver.

1st mode:
position mode
2nd mode:
speed mode

PA_001=23

The control mode is switched through external input.

1st mode:
position mode
2nd Mode:
torque mode

PA_001=24

The control mode is switched through external input.

1st mode:
speed mode
2nd Mode:
torque mode

PA_001=25

The control mode is switched through external input.

The step of changing the operation mode:

1, Switch the driver to Servo Off status.

2, Modify the corresponding parameters of control mode to EEPROM.

Turn off/on the power to make the new mode works after setup completed.

7.3.2 Position Mode

The driver is widely used for precise positioning in position control mode.

Содержание ELD5 Series


















































































Результаты поиска

Содержание ELD5 Series

Отзывы:

Похожие инструкции для ELD5 Series

Бренды по названию

Популярные бренды

Leadshine ELD5 Series, Руководство пользователя

Результаты поиска

Содержание ELD5 Series

Отзывы:

Похожие инструкции для ELD5 Series

Бренды по названию

Популярные бренды