background image

 

CHAMELEON SAFETY INSTRUCTIONS 

Document last reviewed: January 2020 

These  safety  instructions  are  complementary  to,  and  in  addition  to  those 
instructions  in  the  main  Manual  section.  Both  should  be  read  and 
understood thoroughly before use of the Chameleon. 

 

It  is  the  responsibility  of  the  user  to  be  fully  aware  of  all  potential 
consequences and actions when using this machine. 

 

The  manufacturer  cannot  be  held  responsible  for  events  occurring  due  to 
use of this machine by unqualified or untrained personnel. 

 

           

Warning: 

All directions in the manual should be read thoroughly and 

completely understood before any attempt to use the machine. 

The machine should only be operated by or under the instruction of 
trained personnel. 

Any  maintenance  of  the  machine  should  only  be  carried  out  by  the 
manufacturer or after the manufacturers strict approval. 
Should  there  be  any  doubt  as  to  the  safety  of  operation  of  the  machine 
under  any  circumstances,  the  machine  should  be  taken  out  of  service 
immediately. 
The  Chameleon  must  not  be  used  in  confined  spaces,  under  any 
conditions of rain, snow or precipitation of any fluids, or moving air which 
will cause the flame to divert from a vertical path. 

           

Warning: 

Failure to observe correct operating procedures may lead to 

serious injury, damage by fire, or explosion. 

 

           

Warning: 

Before initial use, and each subsequent use, the Chameleon 

should be checked for functional suitability. Should any damage be 
observed or doubt about suitability of use occur, it should be immediately 
decommissioned  and  held  for  service.  The  Chameleon  should  not  be 
subjected to temperatures below 5 degrees Celsius or above 45 degrees 
Celsius nor exposed to unsheltered conditions. 

 

           

Warning: 

It should always be assumed that gas remains within the 

Chameleon  system.  Never  assume  otherwise.  The  Chameleon 
should  be  purged  of  gas  as  described  in  the  manual  either  by 
flaming, or safely releasing the gas. 

Содержание Chameleon














Отзывы: