Introduction:
You have purchased a kit for your model railway supplied within the assortment of
L
ittfinski
D
aten
T
echnik (
LDT
). These kits are of high quality and easy to assemble.
We are wishing you having a good time for assembling and application of this
product!
General:
Tools required for the assembly
Please assure that the following tools are available:
•
a small side cutter
•
a mini soldering iron with a small tip
•
solder tin (if possible 0,5mm diameter)
Safety Instructions
•
All electrical and electronic components included in this kit shall be used on low
voltage only by using a tested and approved voltage transducer (transformer). All
components are sensitive to heat. During soldering the heat shall be applied for a
very short period only.
•
The soldering iron develops a heat up to 400°C. Please keep continual attention to
this tool. Keep sufficient distance to combustible material. Use a heat resistant pad
for this work.
•
This kit contains small parts which can possibly be swallowed from children.
Children (especially under 3 years) shall not participate on the assembly without
supervision.
Assembly List:
Pos. Qty. Components
Remarks
Ref.
Done
1
1 Printed circuit board
DB-4 Rev. 1.4
2
2 Resistors 0,1 Ohm
Marked: "R10"
R1, R2
3
1 Resistor 10 Ohm
brown-black-black-gold
R3
4
1 Resistor 100 Ohm
brown-black-black-black
R4
5
1 Resistor 180 Ohm
brown-gray-black-black
R5
6
2 Resistors 220 Ohm
red-red-black-black
R6, R7
7
1 Resistor 330 Ohm
orange-orange-black-black
R8
8
1 Resistor 470 Ohm
yellow-violet-black-black
R9
9
1 Resistor 1 KOhm
brown-black-black-brown
R10
10
1 Resistor 2,2 KOhm
red-red-black-brown
R12
11
2 Resistors 3,3 KOhm
orange-orange-black-brown
R13, R14
12
2 Resistors 4,7 KOhm
yellow-violet-black-brown
R15, R16
13
4 Resistors 10 KOhm
brown-black-black-red
R11,R18...R20
14
1 Resistor 12 KOhm
brown-red-black-red
R21
15
1 Resistor 27 KOhm
red-violet-black-red
R22
16
3 Resistors 47 KOhm
yellow-violet-black-red
R17,R23,R24
17
1 Resistor 1 MOhm
brown-black-black-yellow
R25
18
1 Network 5*10 KOhm
attend to polarity!
RN1
19
10 Diodes 1N4003
attend to polarity!
D1...4, D6...11
20
3 Diodes 1N5819
attend to polarity!
D5, D12, D13
21
1 Z-Diode BZX ... 5V1
attend to polarity!
D14
22
1 Z-Diode BZX ... 30V
attend to polarity!
D15
23
1 IC-socket 28poles
attend to polarity marking!
IC1
24
3 IC-sockets 8poles
attend to polarity marking!
IC2, 3, 5
25
1 IC-socket 16poles
attend to polarity marking!
IC7
26
1 IC: LTV814
attend to polarity!
IC6
27
1 DC-DC Converter
attend to polarity!
IC4
28
1 Resonator 8MHz
CR1
29
5 Capacitor 100nF
100nF = 104
C1...C5
30
1 Tantalum cap. 1uF/35V
1uF = 105; attend to polarity!
C6
31
3 Tantalum cap. 10uF/10V
10uF = 106; attend to polarity! C7...C9
32
4 Electrolytic cap. 470uF/35V
attend to polarity!
C10...C13
33
1 Storage choke
L1
34
1 DC-socket
BU1
35
2 Sockets 4poles
BU2, BU3
36
1 Socket bar 2x10poles
BU4
37
1 Pin bar 2x5poles
JP1 ... JP5
38
5 Jumpers
set on pin bar 2x5poles
JP1 ... JP5
39
2 Pin bars 5poles
ST1, ST2
40
1 Push button
S1
41
1 LED green plus distance sleeve attend to polarity!
LED1
42
1 LED red plus distance sleeve
attend to polarity!
LED2
43
1 Clamp 2poles
KL1
44
3 Clamps 2poles and 3poles
build block prior to assembly
KL2 ... KL4
45
1 IC: ATMEGA168-20
attend to polarity!
IC1
46
1 IC: LM2574HVN-5
attend to polarity!
IC2
47
1 IC: LM393
attend to polarity!
IC3
48
1 IC: HCPL2631
attend to polarity!
IC5
49
1 IC: LTV847
attend to polarity!
IC7
50
4 Cross headed screws M3x6
for assembly "DB4-Power"
51
2 Distance spacer 18mm
for assembly "DB4-Power"
52
1 DB4-Power
assembly acc. instruction
53
final control
Set-Up:
For the board assembly please follow exact the sequence of the above
assembly list
.
Cross each line off as
done
after completing the insertion and the soldering of the
respective part.
For the
diodes
please keep special attention the correct polarity (marked line for the
cathode).
With reason to different makes of
electrolytic capacitors
you will find different
markings of the polarity. Some are marked with "+" and some are marked with "-".
Each capacitor has to be assembled to the board that the marking on the capacitor is
in correspondence with the marking on the pc-board.
For
tantalum capacitors
please attend to the
connection wire
marked "+". This wire
has to correspond to the printed mark on the pc-board.
