This grill is also shipped with an NG regulator (for natural gas grills) and an LP regulator with hose for grills set up for
liquid propane. NOTE: If you have a grill set up for NG gas type, and it is equipped with a 3/8 NPT Elbow, then a 3/8 male
to 1/2 female straight conversion fitting will be required. A 1/2 NPT female elbow can also be used to replace the
existing elbow.
It is highly recommended that a qualified plumber or gas technician make this installation and perform the gas hook-
up procedure.
1.
Using two or more people, carefully lift the grill onto the island TOP surface next to the cutout. Align the grill
front to back. Measure the distance from the front gas exit point of the manifold (elbow) to the back of the
island. You will need a ½” pipe with ½” NPT male threads at both ends that match this distance plus 2”. This
pipe is called a ‘nipple’. Nipples come pre-threaded at both ends and are available in a variety of different
lengths.
2.
Use pipe joint compound or Teflon tape (to seal the threads) FOR ALL PIPE CONNECTIONS and install this
first pipe into the elbow at the front of the grill.
3.
Using two or more people, carefully lift the grill into the island cutout and slide the grill toward the back of
the cutout. Allow the newly installed pipe to slide through the pre-cut hole or opening and through the back
wall of the island. Slide the grill all the way in so that the front of the grill is flush with the front of the island.
4.
Make your first connection using a ½” NPT female elbow. Point this elbow downward if the main gas supply
is near the ground. If the main gas supply is in a location other than the ground, point the elbow in that
direction.
5.
Install a short nipple into the open end of the elbow and install the supplied NG regulator at the end of this
nipple. Make sure the regulator is installed so the arrow (marked on the regulator) is pointing to the grill,
i.e., in the direction the gas will be flowing.
6.
Measure the distance from the open end of the regulator to the ground and subtract 8” from this
measurement to allow for the next 3 connections. This will be the length of your next nipple.
7.
Install this nipple to the regulator and at the other end, install a ½” NPT female ‘Tee’ connection. The third
(downward) leg of the ‘Tee’ is used to install a 3” minimum length ‘Drip Leg’ with cap. This leg is required in
many states and is used for periodic moisture relief. Check your local codes. This complete pipe routing
should now be resting 1-2 inches above the ground.
8.
Install the next nipple into the center opening of the ‘Tee’ and run this connection to the gas source.
IMPORTANT NOTE: If the gas source does not have a gas shut-off valve, then a new ½” quarter turn valve
MUST be installed between the last gas pipe and the existing gas source. This gas valve should be installed
by a qualified plumber or gas technician. See the next step.
9.
If the gas source is a stubbed gas pipe coming from the side of the house or exit point, then THE GAS MUST
BE TURNED OFF AT THE METER. A new quarter turn gas valve must be installed, either at the gas source or
inline from the gas source in a convenient location.
10.
Use the ‘Leak Test Procedure’ found in the ‘FINAL CHECKS’ section of this manual to check all gas
connections prior to operation of this grill.
INSTALLATION METHOD #1- USING LP GAS (LIQUID PROPANE-BOTTLE)- when using bottled LP, then use the LP
regulator and hose equipped with the LP grill. The installation should begin the same as an NG installation where a ½
NPT pipe (threaded at both ends) is routed from the gas exit elbow at the front of the grill through the rear of the island.
A second ½ NPT elbow is also added at the rear pointing downward and outside of the island rear wall. At this point, the
hard piping is complete. Connect the LP hose end directly to this elbow. Use the above diagram for routing the hose to
the newly installed elbow. As previously mentioned, if the island is constructed in a ‘hollow’ manner, and there is a
hollow space between the back of the cutout and the back of the island, then the hard piping can be routed downward
into the island interior. This piping can terminate with either a ½ NPT female elbow or a ½ NPT straight coupler. The LP
hose can then be attached directly to the ½ elbow or coupler. Always assure that the LP hose is completely visible and
accessible inside the island.
5
Содержание A4TS
Страница 1: ...LazyMan Gourmet Grills USE AND CARE GUIDE OPEN HEARTH SERIES GRILLS ELITE SERIES GRILLS...
Страница 25: ...21...