background image

12

 

PBU-150-11 

09/22 

TROUBLESHOOTING 

Esc

 

WARNING MESSAGES 

LCD Messages 

Warning 

Troubleshooting 

UPS is overloaded – will be shut down 

Overload Warning 

Remove some unnecessary loads. 
If output power turned off, clear the 
warning message in the battery mode.

Low Battery –Shutdown imminent 

Low Battery Warning 

Check the batteries. 

Battery Depleted – UPS has shutdown 

Low Battery Cut-Off 
Warning 

Check the batteries. 

Batt Disconnect 

Battery Disconnected 
Warning 

Check the batteries connections. 
Charging the batteries for 8 hours, and 
then test the PBU again. If this warning 
remains, replacing the batteries is 
recommended. 

 

ERROR MESSAGES 

LCD Messages 

Possible Cause 

Troubleshooting 

Output Short Circuit – UPS has 
shutdown 

Output Short Circuit 

Remove all loads and restart the 
PBU. If this error remains, contact 
customer service. 

Internal Bus Fault – UPS has shutdown

Internal Bus Fault 

Remove all loads and restart the 
PBU. If this error remains, contact 
customer service. 

Inverter / Output Failure – UPS has 
shutdown 

Inverter Failure 

Remove all loads and restart the 
PBU. If this error remains, contact 
customer service. 

Charger Failure - PLS check charger 

Charger not working 

Check the battery capacity and line 
voltage. 

Charger Failure - UPS has shutdown 

Over Charger 

Check the battery capacity and line 
voltage. 

High Internal Temperature – UPS has 
shutdown 

PBU or ambient 
temperature is too high 

PBU or ambient temperature is too 
high. 

Fan Failure - PLS replace fan 

Fans might get 
damaged or stuck 

Check or replace the fan. 

Error: 
Output Short Circuit - UPS

Warning/Error LED (Red) 

Warning/Error Messages 

Содержание PBU-150-11















Отзывы: