Pag. 28
UNPACKING
:
Having eliminated the outer packaging, free the machine from the pallet as follows:
1)
Release the front wheel brake
2)
Remove the sticky tape
Detail C
blocking the handlebar
3)
Open the bin
Detail A
and pull out the two handlebar supports
Detail B Fig.1
4)
Screw the handlebar supports
Part. B
into the holes
Part. E Fig. 1
5)
Screw the ends of the handle into the holes
Detail D
on the supports as shown in
Fig.1/B
6) Take the machine off the pallet: according to the machine weight, written on the CE label, this can be
done
in
different ways:
a)
With the aid of one or more people provided with gloves, lift the machine, holding it by handle at the
front, and stand it on the ground.
b)
With the aid of a slanting board (not longer than 80 cm not to damage the dust flaps) placed against the
narrowest side of the bench, slide the machine down until the floor.
IMPORTANT:
C
heck that the machine has not been damaged. In the case of apparent faults, do not attempt to
use the machine and inform the supplier or the manufacturer.
_______________________________________________________________________________________
IT IS DUTY OF THE USER TO ENSURE THAT THE WASTE PACKAGING IS DISPOSED OF
AND DESTROYED ACCORDING TO THE SPECIFIC REGULATIONS.
_________________________________________________________________________________________
ASSEMBLING THE SIDE BRUSH:
1)
Take the side brush
Detail 2 Fig. 2
out of the bin
Detail A Fig. 1
2)
Unscrew and remove the three bolts
Detail 1 Fig. 1
; assemble the brush so that the three pins fit into the holes
Detail 3 Fig. 2
3)
Replace the three bolts
Detail 1
and screw on tightly to block the brush.
4)
Once assembled, the side brush makes contact with
Detail 2 Fig. 2
blocking the pulley where to place the elastic belt
Detail 5 Fig. 1
5)
Pull the belt
Detail 5
forwards and fit it into the plastic pulley
Detail 4
.
6)
Unscrew the screws
Detail 6
: the purpose of these screws is to keep the belt taut while assembling the brush. Once
the brush has been assembled these screws are no more needed.
7)
Secure the cover
Detail 1 Fig. 3
using the three screws
Detail 2 Fig. 3
.
CHAPTER 4 - PERMITTED ENVIRONMENTAL CONDITIONS
FOR THE ENDOTHERMIC VERSIONS:
MINIMUM WORKING TEMPERATURE
- 28° C
(- 18,4° F)
MAXIMUM WORKING TEMPERATURE
+ 38° C (+ 100
°
F)
FOR THE ELECTRIC VERSIONS:
MINIMUM WORKING TEMPERATURE
- 20° C
(- 4° F)
MAXIMUM WORKING TEMPERATURE
+ 40° C (+ 104° F)
IMPORTANT:
Do not use or leave parked with temperatures above +45° C (+113° F).
CHAPTER 5 – PERMITTED AND FORBIDDEN USES
PERMITTED USES:
The
SWL 700/900 – SW 2600/SW 3700
sweeping machines are designed for cleaning ground surfaces under the following
conditions: types of material to be swept up from ground: machining residues, dust, grit, dirt in general; types and features
of working surfaces (ground): hard, flat and compact surfaces such as: asphalt, concrete, wood surfaces, metallic surfaces,
ceramics, marble, smooth or rusticated plastic materials fibre or synthetic (to avoid electrostatic charges on these surfaces,
natural fibre brushes are essential.) cut moquette; type of environment: closed environments (electric versions), open
environments (endothermic versions).
FORBIDDEN USES:
Содержание SW 2600 BT
