LAUREL LAUREATE 2 Series Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 64

background image

- 59 -

24. GLOSSARY OF TERMS

Adaptive Filter Threshold

A threshold which causes an adaptive moving average filter to be reset to the

latest reading when the accumulated difference between individual readings and
the filtered reading exceeds that threshold. Adaptive moving average filtering
allows a meter to respond rapidly to actual changes in signal while filtering out
normal noise. The accumulated difference is also reset to zero when the latest
reading has a different polarity than the filtered reading. A low adaptive filter
threshold is normally selected. A high filter threshold should be selected if the
signal has large transients.

Alarm, Latched

An alarm which stays actuated until reset.

Latched  alarms  can  shut  down  machinery  or  a
process  when  an  operating  limit  has  been
exceeded,  or  maintain  an  alarm  condition  until
acknowledged by an operator.

Alarm, Non-latched

An alarm which changes state automatically

when the reading rises above a specified limit
and changes back automatically when the
reading falls below a limit.

Autofilter

A selectable digital filter mode which automatic-
ally selects an appropriate moving average filter
time constant from 0.08 sec to 9.6 sec for the
encountered noise condition.

Auto-tare

A selectable meter operating mode, where the

first reading following power-on or meter reset is
used to zero the display. Further readings are then relative to this new zero.

Batch Average Filter

A digital filter mode which averages 16 readings and then displays the average.

Readings are taken at 60/sec with 60 Hz power and 50/sec with 50 Hz power.

Counts

The reading displayed on the panel meter ignoring the decimal point. One count

= one unit of resolution.

Custom ASCII Protocol

A simplified, short protocol for use with these

panel meters. It allows 31 digital addresses.
Not an industry-standard protocol, like the more
complex

Modbus protocol

, which is also offered

with the meters.

Deviation Band

A band in counts which controls relay action

symmetrically around a

setpoint

. The relay

actuates when the reading falls within the

«
...
57
58
59
60
61
...
»

Содержание LAUREATE 2 Series

































































Отзывы:

Нет отзывов

Похожие инструкции для LAUREATE 2 Series

Бренд: Eaton Страницы: 53

Бренд: Oceanic Страницы: 75

Бренд: Cecomp Страницы: 4

Бренд: Trotec Страницы: 14

Бренд: Isspro Страницы: 2

Бренд: Omega Страницы: 13

QI-POWER-485-300-LV

Бренд: QEED Страницы: 2

Бренд: Trotec Страницы: 3

Бренд: wattwatchers Страницы: 14

Бренд: X-Rite Страницы: 54

Бренд: Roland Страницы: 224

Бренд: Chauvin Arnoux Страницы: 12

Бренд: Gait up Страницы: 17

Бренд: ATIM Страницы: 32

Бренд: Kobold Страницы: 27

wtw Cleaning Air Box -115 VAC

Бренд: Xylem Страницы: 32

Бренд: NI Страницы: 20

Бренд: R-Biopharm Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды