LAUREL LAUREATE 2 Series Скачать руководство пользователя страница 16

Страница: 16 / 64

- 16 -

Press Menu
Select Key

Press Digit
Select Key

Press Value Select
Key

ConFG

Meter
Configuration

00_0

Operation as a rate of
change meter.

Extended meter only.

Not rate of change

Rate x 0.1

Rate x 1

Rate x 10

Rate x 100

Rate x 1000

Rate x 10000

0_0

Operation of front
panel

PEAK

button

and rear connector for
Peak or Valley Display

Peak Display. Also selects “Peak” in

“Peak or Valley” at connector above.

Valley Display. Also selects “Valley” in

“Peak or Valley” at connector above.

Peak (1st push), Valley (2nd push)

Front panel Tare

Auto-tare

Meter comes up in normal run mode.

Meter comes up in auto-tare mode.

000_

Linear or nonlinear
input scaling

Linear input

Custom curve linearization

Extended meter only.

FiLtr

Filtering

0000

Alarm filtering

Unfiltered output

Filtered output

000

Peak & Valley filtering

Unfiltered Peak & Valley

Filtered Peak & Valley

Display filtering

Display 16-reading batch average every
17 readings. Updates display 3.5 times/
sec at 60 Hz, 3.0 times/sec at 50 Hz.

Display per signal filter setting below.

000

Adaptive filter

threshold for all filters

Low adaptive filter threshold level

High adaptive filter threshold level

0000

Input signal filter
setting.

Can be applied to dis-
play, setpoint, analog
output, data output.

Autofilter. Time constant set by meter.

Batch average of 16 readings

Moving average, 0.08 sec time constant.

Moving average, 0.15 sec time constant

Moving average, 0.3 sec time constant.

Moving average, 0.6 sec time constant.

Moving average, 1.2 sec time constant.

Moving average, 2.4 sec time constant.

Moving average, 4.8 sec time constant.

Moving average, 9.6 sec time constant.

Unfiltered. Readings updated at 60/sec

at 60 Hz, 50/sec at 50 Hz.

dEc.Pt

Decimal point
selection

dddd

Decimal point flashes.

dddd

ddd

dd dddd

ddddd

Press to shift the decimal point.

Содержание LAUREATE 2 Series

































































Результаты поиска

Содержание LAUREATE 2 Series

Отзывы:

Похожие инструкции для LAUREATE 2 Series

Бренды по названию

Популярные бренды

LAUREL LAUREATE 2 Series, Руководство пользователя

Результаты поиска

Содержание LAUREATE 2 Series

Отзывы:

Похожие инструкции для LAUREATE 2 Series

Бренды по названию

Популярные бренды