latch INT1LFCNA1, Руководство по установке

Страница: 18 / 21

Intercom Installation Guide 34 Version 1.0 35
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the manufacturer responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC
Rules.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance of
20cmbetween the radiator & your body.
Industry Canada (IC) Compliance Statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio / TV technician for help.
Regulatory Compliance
potential for harmful interference to co-channel mobile satellite systems.
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with greater than 20cm between
the radiator & your body.
Le présent appareil est conforme aux CNR d’ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout
brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement
indésirable.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux système de
satellites mobiles utilisant les même canaux.
Déclaration D’exposition aux Radiations
Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de 20cm entre le
radiateur et votre corps.
This section contains information and instructions required for UL compliance. To make sure the
installation is UL compliant, follow the instructions below in addition to the general information
and instructions provided throughout this document. In cases where pieces of information
contradict each other, the requirements for UL compliance always replace general information
and instructions.
Safety Instructions
•
•
•
•
Requirements for Compliance
with UL 294 7th Edition
This product shall be installed and serviced by certified professionals only
Locations and wiring methods shall be in accordance with the National Electrical Code,
ANSI/NFPA 70
For PoE connections, Installation must be done in accordance with NFPA 70: Article 725.121,
Power Sources for Class 2 and Class 3 Circuits
There are no replacement parts available for this product