Rev. A 11/19
4
2680MHDES
MODEL 2680M
OPERATION
This Fan may be operated by the Manual Controls located on
top of the unit (as shown in
Figure 5
) or by the Remote Control
(shown in
Figure 6)
.
1. Place the Fan on a firm and level surface.
2. Plug the cord set into a 120 volt outlet.
Be sure that the plug fits tightly into outlet.
When plugs fit loosely into receptacles, they may
slip partially or completely out of the receptacle with
only the slight movement of the attached cord. Re-
ceptacles in this condition may overheat and pose a
serious fire hazard; if covered by a curtain or drape,
the fire hazard is even greater.
3. Turn the Fan ON by pressing the
Power Button
( ).
4.
SPEEDS:
Press the
Fan Speed Button
(
) to desired speed
setting. Each time the Fan Speed Button is pressed, the speed
will change from High (3), to Medium (2), to Low (1). When intially
plugged in, the Fan will be in High Speed. When the Fan is turned
OFF and ON again, the unit will resume the speed at which it
was turned OFF.
Figure 5
5.
OSCILLATION:
Press the
Oscillation Button
( ) to start and
stop the oscillation function.
6.
TIMER:
The timer function allows the unit to be set to operate
for a length of time from 1/2 hour to 7 1/2 hours, in increments
of a 1/2 hour. Press the
Timer Button
( ) to set the length of
time desired. Each time the timer button is pressed, the time is
increased by 1/2 hour. After reaching 7 1/2 hours, pressing the
timer button once more will reset the Fan to continuous running.
The lights on the front of the unit will light up appropriately with
the length of time that the Fan is set for.
7.
SLEEP:
This function allows the unit to be set in Sleep Mode.
Pressing the
Sleep Button
( ) once will set the unit on Low for 6
continuous hours. Pressing the
Sleep Button
( ) again will turn
Sleep Mode OFF. The
Oscillation Button
( ) will function when
the Fan is in Sleep Mode. Pressing any other button (Timer, Fan
Speed or the Power Button) will shut off the Sleep Mode.
8. To turn the Fan OFF, press the
Power Button
( ) and unplug the
unit from the electrical outlet.
Rev. A 11/19
9
2680MHDES
MODELO 2680M
ARMADO DE LA BASE
(Figura 2)
1. Arme la
Base
entrecerrando las
Copas
en los
Orificios De Copa
situados en la
Parte Inferior De La Base
.
2. Fije
(5)
Tornillos #8 X 1/2" (1,27 cm)
en los
Orificios De Copa
en
la
Parte Inferior De La Base
.
CONJUNTO DE LA CABEZA
(Figura 4)
1.
Coloque el
Conjunto del Cabezal
sobre el extremo del
Extensión
De La Tubería
torciendo
Conjunto del Cabeza
l
abajo hasta que se
siente en el
Extensión De La Tubería
.
(Figura 4)
Figura 4
Extensión De La Tubería
Conjunto del Cabezal
ENSAMBLE DEL PIE
(Figura 3)
COLOQUE LA BASE EN EL PISO
1. Utilizando un movimiento giratorio, inserte el extremo del tubo
de diámetro grande en el agujero de la
Base
. El girar el tubería a
medida que se lo empuja asegura que el tubería quede plenamente
asentado en la base.
2.
PARA AJUSTAR LA ALTURA:
a) Afloje
la
Tuerca De Ajuste De Altura
.
b)
Eleve o baje el
Extensión De La Tubería
hasta obtener la
altura deseada.
c) Apriete
la
Tuerca De Ajuste De Altur
a
.
Base
Extensión De La Tubería
Tuerca De Ajuste De Altura
Figura 3
Conjunto del Cabezal
Figura 2
(5)
Tornillos #8 X 1/2" (1,27 cm)
Copas
PARTE INFERIOR DE LA BASE
Orificios
De Copa
Figura 1
Extensión De
La Tubería
Tuerca De
Ajuste De
Altura
Paso 1
Paso 2
Paso 3
Paso 4
Extensión De
La Tubería
Tuerca De
Ajuste De
Altura
HERRAMIENTAS NECESARIAS PARA EL
ARMADO
(no incluida)
- Destornillador de Cabeza Phillips # 2
ARMADO DE LA TUBERÍA
(Figura 1)
1. Saque el conjunto de la tubería del cartón como muestra.
(Paso 1)
2. Desafloje la
Tuerca De Ajuste De Altura
, girando en sentido con-
trahorario.
(Paso 2)
3. Eleve
la
Extensión De La Tubería
.
(Paso 3)
4. Apriete
la
Tuerca De Ajuste De Altura
, girando en sentido horario.
(Paso 4)