![background image](http://html1.mh-extra.com/html/comfort-maker/cmfan12/cmfan12_installation-instructions_2641445001.webp)
Make the connection as per the wiring diagram, then reposition the back
cover. Tuck the excess wire back into the ceiling.
Note: Ensure that the power is turned off before carrying out any work on
electrical installations.
6. Fit the in-house end of the duct to the fan outlet.
Note: Keep the route as straight as possible.
7. Position the housing into the hole
Choose an optimal direction to put the housing into the hole in accordance
with the position of fan outlet. Use the spring clips to fix the housing.
Ensure that the unit is held securely by the clips.
Note: Try to keep the redundant wire away from the housing.
8. Final Installation
1) Replace the Fascia
Replace the fascia and retaining springs.
2) Replace the Lamps
Ensure the lamps are tightened sufficiently to make good electrical
contact. Clean the lamps and fascia.
3) Fix the Switch Panel to the Wall
Fit the switch panel onto the wall, ensuring that in this position it is not
subjected to splashed water.
Note: The switch wiring should be routed inside the wall. If it is necessary
to run the wiring on the outside of the wall, use a suitable conduit and fixings
to properly locate and hold the wiring used.
USE
Our bathroom heat/fan/light unit uses the infrared heating lamps as a source of heat. It also combines the functions
of exhaust and light.
1. Heat
'HEAT' button On/Off
Each individual infrared lamp has been sprayed with 4ºC cold water to ensure that there are no flaws in the
construction.
Note: Do not touch the infrared lamps with any part of your body when in use.
2. Exhaust
'FAN' button On/Off
This unit can exhaust odours and steam in a quick and efficient way by turning on the "FAN" button.
3. Lighting
'Light' button On/Off
Note: Do not switch on/off frequently when in use. Shut off the power if in long vacancy.
MAINTENANCE
1. Clean
1) Shut off the power before cleaning.
2) Wipe lamps and fascia with care using a soft cloth soaked with
a neutral detergent.
Note: Ensure the lamps are cool to touch before handling.
2. Lamp Replacement
1) Check and tighten lamps regularly.
2) Shut off power before replacement.
3) Use an ES27 LED lamp for lighting.
4) Use ES27 275W infrared lamps for heating. (LHT0081)
Note: It may affect operation (even cause danger) if lamps other
than the designated ones are used.
WARRANTY - 2 YEARS (excluding lamps)
The main unit and fan motor is warranted against factory fault for
a period of 2 years. Labour costs are not covered. Please keep
and bring the original invoice to your place of purchase for
warranty services.
This warranty does not cover damage or loss caused by:
1) LED lamp or failure of LED lamp.
2) Any consequential losses arising from incorrect installation or
operation or maintenance of this product.
3) Any consequential losses arising from incorrect wiring of this
product.
4) Any consequential losses arising from repairing of any part of
this product by unauthorised persons.
Fill out the following details and file with the purchase invoice for warranty service.
BATHROOM 2 HEAT/FAN/LIGHT
MODEL NO. CMFAN12
Purchased from:
Date of purchase:
We reserve the rights to revise this instruction without any prior notice.
Read and save these instructions!
Please take this card as hole cutting template 390mm x 220mm.
MAIN TECHNICAL PARAMETERS
Model Number
CMFAN12
Rated Voltage
220V-240V
Rated Frequency
50Hz
Rated Power
630W
LIST OF ACCESSORIES
Operation unit
1 piece
Infrared lamp (ES27)
2 pieces
LED lamp (ES27)
1 piece
Installation instruction &
hole-cutting template
1 piece
1.5 metres flexible ducting
1 piece
Grille
1 piece
Duct clip
2 pieces
Switch
1 piece
INSTALLATION INSTRUCTIONS AND HOLE-CUTTING TEMPLATE