background image

 

 

Figure 3

 

 
 
 
      Connections Required for System 

 

Larkin S/S 12” x 22” x 6” AFC Control Box with hinged door and switches:  
 

- Low Voltage wiring to hood sensor(s) 

-

 

Wiring to lights in hood(s) 

-

 

Fire suppression micro switch wiring 

-

 

Two separate circuits wired from breaker panel: 

   

     (1)120VAC 15AMP for control voltage 

      

 (1)120VAC 15AMP for hood light(s) 

E -

 1 or 3 Phase power as required wired from breaker panel to Control Box for fan(s) (See wiring diagram) 

F -

 1 or 3 Phase wired from Control Box to fan(s) (See wiring diagram) 

G -

 *1 or 3 Phase power (if Tempered MUA is provided) wired from breaker panel to Tempered MUA unit.

  

 

 

*Note: 

If Tempered MUA is provided, the input power wiring for the Tempered MUA unit must be 

connected directly from the breaker panel (G) and a separate Run-Stop control circuit connected from the 
Control Box terminals R and G to the Tempered MUA unit control panel terminals R and G.     
 

- *Low voltage Run-Stop control wiring (if Tempered MUA is provided) from the Control Box to the Tempered MUA 

unit. * 

 

 

 

Содержание Auto Fan Control















Отзывы: