Lantronix SGX 5150 Скачать руководство пользователя

Страница: 25 / 142

3: Installation of the SGX 5150

SGX 5150 IoT Device Gateway User Guide

Table 3-4 Serial RJ45 Connector Pinout and LEDs

Note:

For the proper operation of the RS422/485

4-wire, the 2-wire modes, as well as the RS232
mode, a GND (Ground) wire must be connected
between the equipment.

USB Connection

One USB 2.0 HS/FS port with
USB type C connector is
available on the SGX 5150 and
can be configured in two ways:



As a USB device (default
setting) where the SGX 5150
can be powered by a VBUS
5V.



As a USB configurable host
where the SGX 5150 can
provide VBUS 5V 0.5A if
powered by a Lantronix
provided wall adapter or PoE
(hardware optional).

Pin Number

Signal Name for RS-232

Signal Name for
RS-422/485 (4 wire)

Signal Name for
RS485 2-Wire

RTS (output from SGX)

TX+ (output from SGX)

TX+/RX+

DTR (output from SGX)

Not used/do not connect.

Not used/do not connect

TXD (output from SGX)

TX- (output from SGX)

TX-/RX-

GND

RXD (input to SGX)

RX+ (input to SGX)

Not used/do not connect

DCD (input to SGX)

Not used/do not connect.

Not used/do not connect

CTS (input to SGX)

RX- (input to SGX)

Not used/do not connect

Right LED

Yellow for Transmit Data
activities (TXD)

Yellow for Transmit Data
activities (TX)

Left LED

Green for Receive Data
activities (RXD)

Green for Receive Data
activities (RX)

Figure 3-5 RJ45 Serial Port

Table 3-6 USB Type C Connector Pinout

Upper Row Pin
Number

Lower Row Pin
Number

Signal Name

Ground

No Connection

VBUS 5V

CC1

CC2

Data+

Data-

No Connection

VBUS 5V

A10

B10

No Connection

A11

B11

No Connection

A12

B12

Ground

Содержание SGX 5150















































































































































Результаты поиска

Содержание SGX 5150

Отзывы:

Похожие инструкции для SGX 5150

Бренды по названию

Популярные бренды

Lantronix SGX 5150, Руководство пользователя

Результаты поиска

Содержание SGX 5150

Отзывы:

Похожие инструкции для SGX 5150

Бренды по названию

Популярные бренды