background image

   

MatchPort b/g Pro Integration Guide 

Copyright and Trademark  

© 2011 Lantronix. All rights reserved. No part of the contents of this book may be 
transmitted or reproduced in any form or by any means without the written permission of 
Lantronix. Printed in the United States of America.  

MatchPort®, with its patent-pending technology, is a trademark of Lantronix. Ethernet is a 
trademark of XEROX Corporation. UNIX is a registered trademark of The Open Group. 
Windows is a trademark of Microsoft Corp.  

Contacts 

Lantronix Corporate Headquarters

 

167 Technology Drive 
Irvine, CA 92618, USA 
Phone:  949-453-3990 
Fax:     949-450-7249 

Technical Support

 

Online:  

www.lantronix.com/support

 

Email/Chat:  

www.lantronix.com/support

 

Sales Offices

 

For a current list of our domestic and international sales offices go to the Lantronix web 
site at 

www.lantronix.com/about/contact/

Disclaimer and Revisions  

Operation of this equipment in a residential area is likely to cause interference to other 
devices, in which case the user, at his or her own expense, will be required to take 
whatever measures may be required to correct the interference. 

Note:

 

This product has been designed to comply with the limits for a Class B 

digital device pursuant to Part 15 of FCC and EN55022:1998 Rules when 
properly enclosed and grounded. These limits are designed to provide 
reasonable protection against radio interference in a residential installation. This 
equipment generates, uses, and can radiate radio frequency energy, and if not 
installed and used in accordance with this guide, may cause interference to radio 
communications.

 

Changes or modifications to this device not explicitly approved by Lantronix will void the 
user's authority to operate this device. 

Note:

 

With the purchase of MatchPort b/g Pro, the OEM agrees to an OEM 

firmware license agreement that grants the OEM a non-exclusive, royalty-free 
firmware license to use and distribute the binary firmware image provided, only to 
the extent necessary to use the MatchPort b/g Pro hardware. For further details, 
please see the MatchPort b/g Pro OEM firmware license agreement. 

Disclaimer  

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates, uses, and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one of the following measures: 

Содержание MatchPort b/g Pro


































Отзывы: