manualshive.com logo in svg

Lantronix Maestro E205XT02, Руководство пользователя, Страница: 84 / 213

Поделиться
Скачать
Lantronix Maestro E205XT02 Скачать руководство пользователя страница 84

 

 

Network 

E220 Series Cellular Router User Guide 

 

84 

Parameters 

Description 

ready. 

 

The default modem initiation timeout 20 seconds. 

Use default gateway 

Click to configure a default gateway route. 

None of the gateway routes are configured by default.  

Use gateway metric 

Enter the gateway metric. 

 

The default metric is 5. 

Use DNS server advertised by 
peer 

Allows the router to advertise the DNS server address. 

 

Use DNS server advertised by peer for 3G interface is checked by 
default. 

LCP echo failure threshold 

Presume peer to be dead after configured LCP echo failures. Use 0 
to ignore failures. 

LCP echo interval 

This is time the router should wait before sending an echo request to 
check whether the link is alive or not. 

 

The LCP echo interval by default is 20 seconds. 

 

Inactivity timeout 

The Router will wait for the LCP echo request response for the LCP 
Echo interval defined after every attempt. It declares LCP link as 
closed if it does not receive response after this defined period of 
attempts 

 

Use 0 seconds to persist the connection. 

Table 10.1-10: Advance Configuration of CELLULAR Interface

 

 

 

Содержание Maestro E205XT02






















































































































































































































Отзывы:

Нет отзывов