Lantronix Maestro E205XT02 Скачать руководство пользователя страница 75

Страница: 75 / 213

Network

E220 Series Cellular Router User Guide

B. Advanced Settings

Screen 10-4: Advanced Configurations for Cellular Interface

Parameters

Description

Bring up on boot

Allows the Cellular interface to be live after every reboot.

Bring up on boot for Cellular interface is checked by default.

Use builtin IPv6 –management

Allows to use the built in IPv6 management configuration.

Enable IPv6 negotiation on
PPP link

Click to enable IPv6 negotiation on PPP link.

Modem init timeout

Enter the maximum wait time in seconds for the modem to become
ready.

The default modem initiation timeout 20 seconds.

Use default gateway

Click to configure a default gateway route.

None of the gateway routes are configured by default.

Use gateway metric

Enter the gateway metric.

The default metric is 7.

Use DNS server advertised by
peer

Allows the router to advertise the DNS server address.

Use DNS server advertised by peer for Cellular interface is checked
by default.

Содержание Maestro E205XT02






















































































































































































































Результаты поиска

Содержание Maestro E205XT02

Отзывы:

Lantronix Maestro E205XT02, Руководство пользователя, Страница: 75 / 213

Результаты поиска

Содержание Maestro E205XT02

Отзывы: