Lantronix 4120 Series Скачать руководство пользователя страница 81

Страница: 81 / 142

Lantronix

x4120 User Guide

33551 Rev. C

https://www.lantronix.com/

Page

142

Fail to set aging time!
Get aging time failed!
CLI command remove fwddb all failed
Redundancy is not supported on this card!

Fail to set SSH server state!

Fail to set management VLAN id!

Fail to set management VLAN state!

Cannot show port QoS configuration in this card!

Cannot set tag type for priority in this card!

Cannot set default priority in this card!

Cannot set IEEE tag for priority in this card!
Cannot set VLAN network tagging on this port!

Cannot show system information on this card!

Cannot create VLAN database on this card!
Cannot remove vlan on this card!
Cannot remove forward database rows on this card!

Cannot set bandwidth alloc type on this card!

Cannot set ingress and egress rate on this card!

The specified conn-port does not exist!

The specified monitor-port does not exist!

Cannot show cable length for fiber port!
Get DMI identifier no such object.
Get SNMP version no such object.
Fail to get cable length

Can not set speed on this port!
Fail to set port advertisement capability!

Fail to get system name!

Set system name timeout.

Get HTTPS state no such object.

Get management VLAN state no such object.

IP management state no such object.

L2CP is not supported on this card!

Link OAM is not supported on this card!

No Time-domain reflectometer support on this card!

You entered a command for a function not supported on the card.

6. Verify the command entry.

7. Verify if the card supports the desired function.

8. Use the

command to switch to a different card port supporting VLAN.

9. Verify the command entry.

10. If the problem persists, contact Technical Support.

Содержание 4120 Series















































































































































Результаты поиска

Содержание 4120 Series

Отзывы:

Похожие инструкции для 4120 Series

Бренды по названию

Популярные бренды

Lantronix 4120 Series, Руководство пользователя

Результаты поиска

Содержание 4120 Series

Отзывы:

Похожие инструкции для 4120 Series

Бренды по названию

Популярные бренды