Lantech LGS-2624C Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 279

Lantech LGS-2624C Скачать руководство пользователя страница 64

Parameter description:

Ingress Port

Indicates the ingress port of the ACE. Possible values are:
Any: The ACE will match any ingress port.
Policy: The ACE will match ingress ports with a specific policy.
Port: The ACE will match a specific ingress port.

Frame Type

Indicates the frame type of the ACE. Possible values are:
Any: The ACE will match any frame type.
EType: The ACE will match Ethernet Type frames. Note that an Ethernet
Type based ACE will not get matched by IP and ARP frames.
ARP: The ACE will match ARP/RARP frames.
IPv4: The ACE will match all IPv4 frames.
IPv4/ICMP: The ACE will match IPv4 frames with ICMP protocol.
IPv4/UDP: The ACE will match IPv4 frames with UDP protocol.
IPv4/TCP: The ACE will match IPv4 frames with TCP protocol.
IPv4/Other: The ACE will match IPv4 frames, which are not
ICMP/UDP/TCP.
IPv6: The ACE will match all IPv6 standard frames.

Action

Indicates the forwarding action of the ACE.
Permit: Frames matching the ACE may be forwarded and learned.
Deny: Frames matching the ACE are dropped.

Rate Limiter

Indicates the rate limiter number of the ACE. The allowed range is 1 to 16.
When Disabled is displayed, the rate limiter operation is disabled.

Port Copy

Indicates the port copy operation of the ACE. Frames matching the ACE
are copied to the port number. The allowed values are Disabled or a
specific port number. When Disabled is displayed, the port copy operation
is disabled.

Mirror

Specify the mirror operation of this port. The allowed values are:
Enabled: Frames received on the port are mirrored.
Disabled: Frames received on the port are not mirrored.

«
...
62
63
64
65
66
...
»

Содержание LGS-2624C
























































































































































































































































































Отзывы:

Нет отзывов