Lantech LGS-2624C Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 279

Lantech LGS-2624C Скачать руководство пользователя страница 108

2-6.5 Group Infermation

The section describes user could set the MLD Snooping Groups
Information. The "Start from VLAN", and "group" input fields allow the user
to select the starting point in the MLD Group Table

Each page shows up to 99 entries from the MLD Group table, default being
20, selected through the "entries per page" input field. When first visited,
the web page will show the first 20 entries from the beginning of the MLD
Group Table.

Web Interface

To display the MLD Snooping Group information in the web interface:

1. Click Configuration, MLD Snooping, Group Information
2. If you want to auto-refresh the information then you need to evoke the

―Auto-refresh‖

3.

Click ― Refresh― to refresh a entry of the MLD Snooping Group

Information.

4. Click

― Clear― to clear the MLD Snooping Groups information..

Parameter description:

Navigating the MLD Group Table

Each page shows up to 99 entries from the MLD Group table, default being
20,  selected  through  the  "entries  per  page"  input  field.  When  first  visited,
the  web  page  will  show  the  first  20  entries  from  the  beginning  of  the  MLD
Group Table.The "Start from VLAN", and "group" input fields allow the user
to select the starting point in the MLD Group Table. Clicking the button will
update the displayed table starting from that or the next closest MLD Group
Table  match.  In  addition,  the  two  input  fields  will  -  upon  a  button  click  -
assume the value of the first displayed entry, allowing for continuous refresh
with  the  same  start  address.The  will  use  the  last  entry  of  the  currently
displayed as a basis for the next lookup. When the end is reached the text
"No  more  entries"  is  shown  in  the  displayed  table.  Use  the  button  to  start
over.

2-6.6 IPv6 SSM Information

The section describes the user to configure the Entries in the MLDv2

«
...
106
107
108
109
110
...
»

Содержание LGS-2624C
























































































































































































































































































Отзывы:

Нет отзывов