Lantech IPES-3408 Series Скачать руководство пользователя

Страница: 3 / 59

1.2 Software Features

Management

SNMP v1 v2c, v3/ Web/Telnet/CLI

SNMP MIB

RFC 1215 Traps MIB,

RFC 1213 MIBII,

RFC 1157 SNMP MIB,

RFC 1493 Bridge MIB,

RFC 2674 VLAN MIB,

RFC 1643 EtherLike,

RFC 1757 RMON,

RSTP MIB,

Private MIB,

LLDP MIB

ITU G.8032

Support ITU G.8032 v2 for Ring protection in less than

10ms for self-heal recovery < 256 switches which can be

compatible with other ITU G.8032 metro switches

Support various ring/chain topologies

Ring covers data & multicast* packets

Pro-Ring 2se*

Self-healing recovery in less than 20ms for Single Ring

topology < 50switches

User friendly UI

Auto topology drawing

Topology demo

Auto configuration for G.8032*

Port Trunk with

LACP

LACP Port Trunk: 4 Trunk groups/Maximum 4 trunk

members

Load balancing through LACP to distribute load*

LLDP

Supports LLDP to allow switch to advise its identification

and capability on the LAN

CDP

Cisco Discovery Protocol for topology mapping

PoE

Management

PoE Detection to check if PD is hang up then restart

the PD

PoE Scheduling to On/OFF PD upon routine time

table

VLAN

Port Based VLAN

IEEE 802.1Q Tag VLAN (256 entries)/ VLAN ID (Up to 4K,

VLAN ID can be assigned from 1 to 4096.)

GVRP (256 Groups)*,GMRP*, MVRP (Multi VLAN

Registeration)*, QinQ

IPv6

Support dual stack for IPv4 and IPv6

Support Plug and Play function

IPv6 Logo Committee certified

Perform with following RFCs:

1. RFC 2460 IPv6 Specification

2. RFC 4861 Neighbor Discovery for IPv6

3. RFC 4862 IPv6 Stateless Address Auto-configuration

4. RFC 1981 Path MTU Discovery for IPv6

Network Security

Support 10 IP addresses that have permission to access

the switch management and to prevent unauthorized

intruder.

802.1X access control for port based and MAC based

authentication/MAC-IP-Port binding

Management access control with priority *

256 Policy based Access Control List*

SSL/ SSH for Management

Содержание IPES-3408 Series




























































Результаты поиска

Содержание IPES-3408 Series

Отзывы:

Похожие инструкции для IPES-3408 Series

Бренды по названию

Популярные бренды

Lantech IPES-3408 Series, Руководство пользователя

Результаты поиска

Содержание IPES-3408 Series

Отзывы:

Похожие инструкции для IPES-3408 Series

Бренды по названию

Популярные бренды