Lange Originals HOIST-A-TOP JT CRANK Скачать руководство пользователя страница 2

Safety Requirements 

Please Read!  

Please thoroughly  read and understand these instruc

ons before installing 

your Hoist-A-Top® and before li

ing your top.  

When installing the Hoist-A-Top® remember safety 

rst! Make sure you use 

proper safety equipment when installing this product. Use gloves and eye 

protec

on. Be careful on ladders. If you are unsure about installing this 

product  consult a professional or call us at the factory. 

Cautions: 

Make sure your garage or structure is  capable of suppor

ng the weight

of your top. If there is any ques

on  about your structure’s integrity,

consult a professional.

Before li

ing your top make sure that all hardware is properly fastened

to  the center of your studs in your wall and ceiling. Wire clamps must

be checked and 

ghtened regularly.

Do a dead weight li

 to ini

�al

ly test your installa

on.

Upon li

ing your top for the 

rst 

�m

e and subsequent 

�m

es therea

er

visually and check that  all hardware including but not limited to  wire

clamps , elevator bolts, hooks , wire cable, crank hoist, and li

ing strap.

Make sure all are 

ght and in good working order.

Lange Originals is not responsible for damage or personal injury due to

improper installa

on, custom installa

on that doesn't follow the

instruc

ons, or neglect to inspect equipment prior to using equipment.

If you need help for any reason DO NOT CALL YOUR DEALER Please contact 

us direct at the factory. We can help with missing parts or for help with 

installa

on.  

Call toll free  1-866-284-7428 or email at [email protected]

 

Call toll free 1866 284 7428 

langeoriginals.com copyright 

lange originals 2017 

Содержание HOIST-A-TOP JT CRANK















Отзывы: