background image

11

 

OPERATION  

GENERAL

 

The Lang Electric Cheese-melter can be used to poach, sauté and brown.  In addition 
to melting cheese on sandwiches, French onion soup, hot apple pie and casseroles, it 
may be used for finishing Italian, Mexican and au gratin dishes utilizing less energy 
than conventional broilers. 

The product is heated with infrared energy provided by quartz heaters.  The rack is 
counterbalanced so that maximum heat is supplied only when the product is placed in 
the rack. 

Although the heating elements are not directly controlled to regulate heat, the 
exposure of the product to heat is adjustable.  Heat adjustment may be obtained by 
raising and lowering the rack position.  The shelf positions provide a choice of 
cooking positions for a variety of applications.  The top position is very hot, and can 
be used for quick browning and toasting, with the heat decreasing at each lower 
position. 

In order to change positions, simply slide the rack in and out of the slots provided.  
Make sure that the end of the rack engages the sliding mechanism located on the right 
front corner. 

CONTROLS

 

Controls are located on the front panel and consist of the following items: 

Power Switch:     

A toggle switch used to turn the unit on and off. 

Heat Switch:

       This toggle switch allows the unit to be operated in either automatic or 

constant modes. 

Automatic

:   

When selected with no product on the rack, the unit is in an 
idle condition.  Placing a product on the rack will energize the 
elements providing heat to the product. 

Constant

:   

When this mode is selected the elements are energized at all 
times whether or not a product has been placed on the rack.  
This mode should be used during peak times only, as it will 
shorten the life span of the elements. 

Side Switch:        

Allows the use of the 

Left

 side only, or 

Both

 sides.  This switch is 

found on Lang Model 

MM48

 Cheese-melters only. 

 
 

CAUTION:

 

ALWAYS KEEP THE AREA NEAR THE APPLIANCE FREE 
FROM COMBUSTIBLE MATERIALS.

 

CAUTION:

 

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND 
DRY.  IF SPILLS OCCUR, CLEAN IMMEDIATELY, TO 
AVOID THE DANGER OF SLIPS OR FALLS.

 

 

 
 

Содержание MM24



















Отзывы: