background image

 

4

IMPORTANT READ 

FIRST 

IMPORTANT

 

CAUTION:

 

EACH UNIT IS EXTREMELY HEAVY.  FOR SAFE 
HANDLING, INSTALLER SHOULD OBTAIN HELP AS 
NEEDED, OR EMPLOY APPROPRIATE MATERIALS 
HANDLING EQUIPMENT (SUCH AS A FORKLIFT, 
DOLLY, OR PALLET JACK) TO REMOVE THE UNIT 
FROM THE SKID AND MOVE IT TO THE PLACE OF 
INSTALLATION.

 

CAUTION:

 

ANY STAND, COUNTER OR OTHER DEVICE ON 
WHICH THE MELTER WILL BE LOCATED MUST BE 
DESIGNED TO SUPPORT THE WEIGHT OF THE 
MELTER. 

CAUTION:

 

SHIPPING STRAPS ARE UNDER TENSION AND CAN 
SNAP BACK WHEN CUT. 

DANGER:

 

THIS APPLIANCE MUST BE GROUNDED AT THE 
TERMINAL PROVIDED.  FAILURE TO GROUND THE 
APPLIANCE COULD RESULT IN ELECTROCUTION 
AND DEATH. 

WARNING:

 

INSTALLATION OF THE UNIT MUST BE DONE BY 
PERSONNEL QUALIFIED TO WORK WITH 
ELECTRICITY AND PLUMBING.  IMPROPER 
INSTALLATION CAN CAUSE INJURY TO 
PERSONNEL AND/OR DAMAGE TO EQUIPMENT.  
UNIT MUST BE INSTALLED IN ACCORDANCE WITH 
ALL APPLICABLE CODES. 

NOTICE: 

The data plate is located on the left side of unit 
towards the front. The melter voltage, wattage, serial 
number, wire size, and clearance specifications are 
on the data plate.  This information should be 
carefully read and understood before proceeding 
with the installation. 

NOTICE:

 

The electric cheese melter must be installed more 
than 12 inches above any cooking surface and never 
above any open burners or charbroilers. 

NOTICE:

 

The installation of any components such as a vent 
hood, grease extractors, fire extinguisher systems, 
must conform to their applicable National, State and 
locally recognized installation standards. 

NOTICE:

 

During the first few hours of operation you may 
notice a small amount of smoke coming off the 
melter, and a faint odor from the smoke.  This is 
normal for a new melter and will disappear after the 
first few hours of use. 

CAUTION:

 

ALWAYS KEEP THE AREA NEAR THE APPLIANCE 
FREE FROM COMBUSTIBLE MATERIALS. 

CAUTION:

 

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN 
AND DRY.  IF SPILLS OCCUR, CLEAN IMMEDIATELY, 
TO AVOID THE DANGER OF SLIPS OR FALLS. 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

 

 

 

Содержание MM24



















Отзывы: