background image

13

 

MAINTENANCE & CLEANING 

 

WARNING: 

KEEP WATER AND SOLUTIONS OUT OF CONTROLS.  
NEVER SPRAY OR HOSE CONTROL CONSOLE.

 

CAUTION:

 

MOST CLEANERS ARE HARMFUL TO THE SKIN, 
EYES, MUCOUS MEMBRANES AND CLOTHING.  
PRECAUTIONS SHOULD BE TAKEN TO WEAR 
RUBBER GLOVES, GOGGLES OR FACE SHIELD AND 
PROTECTIVE CLOTHING.  CAREFULLY READ THE 
WARNING AND FOLLOW THE DIRECTIONS ON THE 
LABEL OF THE CLEANER TO BE USED. 

NOTICE:            

Never leave a chlorine sanitizer in contact with 

stainless steel surfaces longer than 10 minutes.  
Longer contact can cause corrosion.

 

Cleaning 

 

Always start with a cold melter. 

 

The stainless exterior can easily be cleaned using Lang Mfg. Prime Shine (72804-
41) oven cleaner. 

 

Always follow the cleaner manufacturer's instructions when using any cleaner. 

 

The melter rack and interior may be cleaned using Lang Mfg. Foam Deluxe 
(

72804-36)

 cleaner. 

 

Discoloration or heat tint may be removed using Lang Mfg. Carbon Release 
(

72804-32)

 cleaner. 

 

Always apply these cleaners when the melter is cold and rub in the direction of the 
metal's grain. 

 

 

 

 
 
 

 

Содержание MM24



















Отзывы: