background image

 

7

 

INSTALLATION

 

DANGER:

 

THIS APPLIANCE MUST BE GROUNDED AT THE 
TERMINAL PROVIDED.  FAILURE TO GROUND THE 
APPLIANCE COULD RESULT IN ELECTROCUTION AND 
DEATH. 

WARNING:

 

INSTALLATION OF THE UNIT MUST BE DONE BY 
PERSONNEL QUALIFIED TO WORK WITH ELECTRICITY.  
IMPROPER INSTALLATION CAN CAUSE INJURY TO 
PERSONNEL AND/OR DAMAGE TO EQUIPMENT.  UNIT 
MUST BE INSTALLED IN ACCORDANCE WITH ALL 
APPLICABLE CODES. 

NOTICE: 

The data plate is located behind the access panel in the 
back of the grill.  If on a 48” or larger, the data plate is 
behind the back left access panel.  The griddle voltage, 
wattage, serial number, wire size, and clearance 
specifications are on the data plate.  This information 
should be carefully read and understood before 
proceeding with the installation. 

NOTICE:

 

The installation of any components such as a vent hood, 
grease extractors, fire extinguisher systems, must 
conform to their applicable National, State and locally 
recognized installation standards.

 

4.1 Electrical Connection 

There is one power supply connection on 2, 3 and 4 foot griddles.  There are two 
power supply connections on 5 and 6 foot griddles.  Refer to the power supply 
chart on the next page for proper power supply size. 

There is (1) one 1 1/4 inch conduit knockout on 2, 3, and 4 foot griddles located at 
the rear of the griddle, through the back and the bottom of the griddle body.  There 
are (2) two 1 1/4 inch conduit knockouts provided on the 5 and 6 foot griddles.  
Use a supply wire suitable for at least 90

°

 C. 

4.2 Griddle Voltage 

This griddle is shipped from the factory wired for 208/240 or 480 volts.  The 
208/240 griddle is a dual voltage design.  Jumper wires on terminal strip next to the 
main power supply connection determine the griddle voltage.  For a 208 volt power 
supply, leave the jumpers in place.  For a 240 volt power supply disconnect the 
jumpers as indicated on the tag to the terminal strip.  The 480 volt griddle can be 
operated on 480 volts only. 

4.3 Phasing 

All griddles are shipped from the factory set up for a 

three phase

 service.  

Rearrange the wires in the power supply terminal block to convert the griddle to 
single phase.  Rephasing the griddle is not chargeable to Star Manufacturing 
International as warranty.  To convert to 

single phase

 follow the chart located on 

the next page. 

 

 

 
 
 
 

 

Содержание CL36GF
















Отзывы: