L&W SC-300 E Скачать руководство пользователя страница 52

Страница: 52 / 89

Page A - 50

LW SC-300 E / LW SC-350 E
Version: 06.12.2022

Oil / water separators final stage

M A I N T E N A N C E A N D S E R V I C E

Oil / water separators final stage - maintenance

Change/clean oil / water separators final stage as follows:

• Loosen pipe connections and mounting screws.

• Remove oil / water separators.

• Open ring nut and remove separator top (Fig. 1).

• Loosen nut at the separator top.

• Change sinter filter (Fig. 2).

• Reassemble all parts and tighten nut.

• Change o-ring, previously grease new o-ring (Fig. 3).

• Place separator top and tighten ring nut manually.

• Replace silencer.

• Mount oil / water separators.

• Tighten pipe connections and mounting screws.

The oil / water separator maintenance is now completed.

Fig. 1 - Loosen ring nut

Fig. 3 - Change o-ring

Fig. 2 - Change sinter filter

Note

Clean all parts thoroughly before assembly.

Содержание SC-300 E


























































































Результаты поиска

Содержание SC-300 E

Отзывы:

Похожие инструкции для SC-300 E

Бренды по названию

Популярные бренды

L&W SC-300 E, Руководство по эксплуатации

Результаты поиска

Содержание SC-300 E

Отзывы:

Похожие инструкции для SC-300 E

Бренды по названию

Популярные бренды