L&W SC-300 E Скачать руководство пользователя страница 15

Страница: 15 / 89

Page A - 13

LW SC-300 E / LW SC-350 E
Version: 06.12.2022

S A F E T Y P R E C A U T I O N S

General Safety Precautions

• Read the Operating Instructions of this product carefully prior to use.

• Strictly follow the instructions. The user must fully understand and strictly observe the

instructions. Use the product only for the purposes specified in the intended use section of this
document.

• Do not dispose the operating instructions. Ensure that they are retained and appropriately used

by the product user.

• Only trained and competent personnel are permitted to use this product.

• Comply with all local and national rules and regulations associated with this product.

• Only trained and competent personnel are permitted to inspect, repair and service the product.

• Only authentic L&W parts and accessories may be used for maintenance work. Otherwise, the

proper functioning of the product may be impaired.

• Do not use faulty or incomplete products. Do not modify the product.

• Inform L&W in the event of any product or component fault or failure.

• The quality of the air supply must meet EN 12021 specifications for breathing air.

• Do not use the product in areas prone to explosion or in the presence of flammable gases. The

product is not designed for these applications. An explosion might be the result if certain
conditions apply.

Содержание SC-300 E


























































































Результаты поиска

Содержание SC-300 E

Отзывы:

Похожие инструкции для SC-300 E

Бренды по названию

Популярные бренды

L&W SC-300 E, Руководство по эксплуатации

Результаты поиска

Содержание SC-300 E

Отзывы:

Похожие инструкции для SC-300 E

Бренды по названию

Популярные бренды