manualshive.com logo in svg

Landoll Brillion Turfmaker II, Руководство оператора

Поделиться
Скачать
Landoll Brillion Turfmaker II Скачать руководство пользователя страница 96

5-8

9K998-0522

MAINTENANCE

Seed Meter Adjustment

IMPORTANT

The Clutch must be disengaged when Seed Shafts 
are turned manually for Calibration.

IMPORTANT

All the Seed Meters MUST BE CLOSED!

All Seed Meters must be set the same to ensure seeding 
uniformity. To check, set the Seed Rate Adjusting Nut to 
0-A. The “A” on the Seed Rate Adjusting Nut is 
positioned over the “0” (the nut covers half of the“0”) and 
snug against the Bearing. 

See Figures 5-6 and 5-7.

Figure 5-6:  Front Seed Box Rate Adjuster

Figure 5-7:  Rear Seed Box Rate Adjuster

All Seed Meters should be closed. Seed Meter Feed 
Shutoff against Seed Meter Cup Star Washer in Seed 
Meter Cup. 

See Figure 5-8.

 If not, there are three 

adjustments to make as needed.

Figure 5-8:  Seed Meter Feed Shutoff

IMPORTANT

Ensure that the Seed Shaft can turn freely without 
any binding when the Seed Meters are open or 
closed after servicing. Seed Box with Large Seed 
Meters you may need to make adjustments to the 
Seed Meter Supports at each Seed Meter Cup. See 
Figure 5-9.

Figure 5-9:  Seed Meter Supports

1. 1/2-13 Locknuts on both ends of the Adjusting Screw 

are used to adjust all Seed Meters the same amount. 

See Figures 5-6 and 5-7.

 To adjust Seed Meters to 

be closed at “0A”, loosen 1/2-13 Locknuts and set 
Adjusting Screw to “0A”. Slide Seed Shaft to close all 
Seed Meters. Tighten 1/2-13 Locknuts against 
Adjusting Screw.

2.

Front Seed Box:

  Adjusting the LH and RH Seed 

Shafts where they join changes Seed Meters on the 
left Seed Box in comparison with Seed Meters on the 
right Seed Box. Remove Seed Shaft Coupling that 
clamps the left and right Seed Shafts together. Turn 
RH Seed Shaft threading it in or out as needed to 
equalize Seed Meters. Re-Install Seed Shaft 
Coupling where the RH and LH Seed Shafts come 
together. 

See Figure 5-10.

DO NOT

Loosen or Adjust

1/2-13 Locknut

 

DO NOT

Loosen or Adjust

1/2-13 Locknut

 

Seed Rate

Adjusting Nut

1-8 Nut

Adjusting

Screw

Seed Shaft

Bearing

DO NOT

Loosen or Adjust

1/2-13 Locknut

 

Seed
Shaft

Seed Rate

Adjusting Nut

Bearing

DO NOT

Loosen or Adjust

1/2-13 Locknut

 

1-8 Nut

Adjusting

Screw

SL2 OpSeedRateAdjRearBox

Seed Meter Cup

Star Washer

)HHG6KXWRႇ

Seed Meter

Cup

Feed Roll

 

Seed Meter

Support

Seed

Meter Cup

Flange Bolt

Содержание Brillion Turfmaker II













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды