manualshive.com logo in svg

Landoll Brillion Turfmaker II, Руководство оператора

Поделиться
Скачать
Landoll Brillion Turfmaker II Скачать руководство пользователя страница 35

ASSEMBLY

9K998-0522

2-19

outside of the Seed Box. To get the Sensor Connector 
outside the Seed Box, feed the terminals through the 
Cord Grip. Install the terminals into the 3-Pin Shroud 
labeled “A”, “B” and “C” as follows “A” White, “B” 
Black, “C” Green. 

See Figure 2-28.

 Inside the Seed 

Box, add enough slack to the Bin Level Sensor Cord 
to allow for future adjustments of the Sensor. Secure 
the Bin Level Cord by tightening the Cord Grip 
Compression Nut. Connect both Bin Level Sensors to 
the Seeder Harness.

Figure 2-28:  Bin Level Sensor Wire Detail

8. Connect the 240" Extensions Harness to the Seeder 

Harness. Route the 240" Extension Harness along 
the Seeder Frame and down the Drawbar/3-PT Hitch 
to the Tractor.

9. Install Brillion Elite Mini Monitor on Tractor. 

See 

“Brillion Elite Mini Monitor Tractor Installation - 
Optional” on Page 2-23.

 

10. If not already installed, install Smart Clutch Relay into 

Elite Mini Tractor Harness 3-Pin Connectors.

11. Connect the Elite Mini Tractor Harness 14-Pin 

Connector to Brillion Elite Mini Monitor, 3-Pin Power 
Plug to 12 Volt Tractor Convenience Outlet and 6-Pin 
Connector to the 240" Extension Harness. 4-Pin 
Connector is not used at this time.

12. Bundle and secure all Harnesses along the Seeder 

Frame and Drawbar/3-PT Hitch with Tie Wraps.

13. Program Bin Level Sensors and Smart Shaft 

Sensors if not already pre-programmed. 

See

 

“Brillion Elite Mini Monitor” on Page 4-1.

Figure 2-29:  Front Seed Box Smart Shaft Sensor Detail

Figure 2-30:  Rear Seed Box Smart Shaft Sensor Detail

White Wire

Black Wire

Green Wire

Terminal

3-Pin Shroud

Shroud Pin ID

Seal

A

A

Seed Shaft,11/16 Hex

SECTION A-A

 1/8" Max 

Sensor

Mount

Smart Shaft 

Sensor

Magnet Wheel

Assembly

Magnet Wheel Assembly

Sensor Mount

Smart Shaft 

Sensor

A

A

Sensor Mount,

4.25 Spacing

Seed Shaft,

3/8 Square

Magnet

SECTION A-A

 1/8" Max 

Smart Shaft Sensor

Magnet

Magnet Collar

3/8 Sq Shaft

Smart Shaft

Sensor

Sensor Mount,

4.25 Spacing

Magnet

Collar

3/8 Sq Shaft

Содержание Brillion Turfmaker II













































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды